HIKVISION Pyronix EURO 280 Скачать руководство пользователя страница 56

Страница: 56 / 72

Page | 56

Wireless Dual Frequency
Menu?

Press the



key to enter this

sub-menu. Select the hub (by
looking at the input range) to see
the following menus:

Channel:

Displays which channel your

control panel is operating on
(either

)

Channel Reason:

Displays the reason why the

panel last switched from one
channel to another.

SF/DF Status:

Displays whether the control
panel is currently operating in

Single (SF) or Dual (DF)
Frequency mode.

NOTE: The

panel will only operate in dual
frequency mode if ALL

peripherals

support dual

frequency (having even one
SF device will default the

whole system into SF mode).

First SF device:

Displays the first Single

Frequency device on your system
(if there is one) this is useful

because the presence of any
single frequency (SF) peripherals
(ZEMS, detectors etc.) will

prevent the whole system from
operating in Dual Frequency (DF)

mode. If there are none it will
display; “All Devices DF”.

Control USB Function?

Press the



key to enter this

sub-menu which is used to switch
the USB functionality between

Disk Drive mode and USB host
mode.

Содержание Pyronix EURO 280









































































Результаты поиска

Содержание Pyronix EURO 280

Отзывы:

HIKVISION Pyronix EURO 280, Руководство по программированию, Страница: 56 / 72

Результаты поиска

Содержание Pyronix EURO 280

Отзывы: