HIKVISION Pyronix EURO 280 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 72

HIKVISION Pyronix EURO 280 Скачать руководство пользователя страница 50

Page | 50

Battery Load Test

EURO 280 Systems may be programmed to perform an automatic battery load test at every
power supply at 7.00am each day. This will drop the power supply voltage below the battery

voltage, whilst monitoring the system diagnostics. The test will NOT take place if:



The End Station siren and strobe Output are live



The system is in Engineer Mode



Any battery faults exists



Any mains fault exists



The site option is not selected

If the test has already started, it will be aborted if any of these conditions apply, other than
entry into Engineer Mode. If the test is aborted, it will NOT be performed until the next day.

This is selected in SITE OPTIONS under “Do Battery Load Test”. The test may also be
performed as required, under engineer control.

4.1.55 Test Outputs

The engineer can test all the Programmable Outputs on the End Station and the output

module. This test can also be used to test the STU/ATE pins, select the output types you have
chosen for the pins and test them, the signal will be then sent out on both the programmable

outputs and the STU/ATE pins.

4.1.56 Test Communications

If the engineer is using SIA or Contact ID to signal events, this function can be used to send a
test signal to the alarm receiving centre (ARC).

4.1.57 Engineer Test Menu

Engineer Tests

Using the



and



keys, scroll to

‘ENGINEER TESTS?

’

Press the



key

Sound To Play

Press the



key to select which

sound you would like to hear. Press the



key.

Walk Test?

Press the



key and Select the Areas

to be tested. Press the



key. The

display will scroll through all the inputs
not yet tested. Walk so that each input

is triggered, and a chime will sound as
inputs disappear from the scrolling list.
Press the



key. Once the last

remaining input has been tested, ‘Walk

Test Complete’ will be displayed, press
the



key to move to the next menu.

NOTE: If a just a specific input needs to be walk

tested, press



instead of selecting areas. This will

then allow specific inputs to be entered with the

numerical keys, pressing



after each input. Then

press



to walk test them.

Soak Control?

To enter the Soak Control press the



key. Enter the number of the

inputs you wish to soak test and press



. The input number shows on the

scrolling list. Repeat for each input to

«
...
48
49
50
51
52
...
»

Содержание Pyronix EURO 280









































































Отзывы:

Нет отзывов