manualshive.com logo in svg

HIKVISION Pyronix EURO 280, Руководство по программированию, Страница: 41 / 72

Поделиться
Скачать
HIKVISION Pyronix EURO 280 Скачать руководство пользователя страница 41

Page | 41 

 

4.1.43 ATE Pin Output (Defaults) 

Any communicating device that is to be connected to the ATE pins/socket on the PCB will have 

the following default output types: 
 

(For the diagram of the communication loom please see the Installation Manual)

: 

 

ATE OUPUTS 

EURO 280 

1 (Blue) 

Fire (0001) 

2 (Orange) 

HU Device Any (0009) 

3 (Yellow) 

Unconfirmed Any (0018) 

4 (Brown) 

Final Set All (0004) 

5 (Purple) 

Tamper Any (0007) 

6 (Green) 

Omit Rearm Any (0017) 

7 (Black) 

Confirmed Any (0006) 

8 (Purple) 

Mains Fail (0052) 

9 (White) 

Global Fault 2 (0056) 

10 (Light Grey) 

Test ATS (0064) 

 

NOTE: There is an “Invert ATE outputs” option for use with positive removed/applied 

signalling Please see ‘Site Options, page 45. 

 

These are programmed in ‘Change Outputs’ under ‘Endstation Output’. 

For programming of the on-board Digi channels please see page: 59 

 

4.1.44 Output Programming 

 

Change Outputs 

Using the 



and 



keys, scroll to 

‘CHANGE OUTPUTS?

’ 

Press the 



key 

 

Endstation Outputs 

To program the control panel 
outputs and the ATE pins press the 



key. 

 

Output Types 

Select the output type for the Output 
and press the 



key. Repeat for 

each output.

 

 

Содержание Pyronix EURO 280









































































Отзывы:

Нет отзывов