background image

 

89 

 

 

The actual access signal must match the signal mode that checked. If 
the "HD" mode is selected for one channel, it can be connected to TVI / 
CVBS / AHD / CVI signals; when the switching signal causes an 
abnormality to be displayed, the video cable can be reconnected; if the 
channel is selected as "IP" mode, then it is an IP channel and IP device 
can be connected. 

 

For preview interface, when the HD (TVI / CVBS / AHD / CVI) channel 
without video signal, the channel name will be prompted "HD VIDEO". 
When the IP channel without video signal, the channel name will be 
prompted "NO VIDEO". 

 

5.3.6.6 Local Alarm 

After the XVR device is connected to the alarm device through the alarm 
input port, when the alarm signal is transmitted to the XVR device through 
the alarm input port, the system performs an alarm linkage action. 

The steps are as follows: 
Step 1:

 On the menu page, select "Configuration →Local Alarm" to enter the 

local alarm configuration interface, as shown in Figure 5-49. 

Step 2:

 Check the Enable "

" to open the local alarm, select the alarm 

input port according to the actual needs, configure the alarm name, time 
period and corresponding linkage alarm, such as "Screen display", "Send 
mail" and "Buzzer alarm". 

Step 3:

 Click "Apply" to save the configuration. 

 

Figure 4-49 

 

Enable:

 Turns on / off local alarm. 

 

Alarm input:

 Select the alarm input. 

Содержание Coaxial HD XVR
































































































































Отзывы: