Hal Communications DKB-2010 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 101

Hal Communications DKB-2010 Скачать руководство пользователя страница 7

5

DKB-2010 SPECIFICATIONS (continued)

Morse Mode

Code:
International Morse

Data Sense:
Keyed: output conducting
Space: output nonconducting

Character Transmission Rate:

Continuously adjustable from less than 8 to
greater than 60 words per minute.

Character Weight:

Any of six weight ratios from 1:7 to 3:1 may be
chosen. A panel switch permits selection of the
four standard weights: Heavy (5:3), normal
(1:1), light (3:5), and very light (1:7). The switch

wiring may be altered to substitute ratios of 1:3

and 3:1 in place of one or two of the standard

weights.

Note:  Character  weight  is  the  ratio  of  dot
duration  to  the  length  of  the  space  between
adjacent  dots  or  dashes.  For  the  normal  weight
ratio of 1:1, the ratio of dot and dash lengths is
1:3. For other weights, dash duration is equal to

the length of two dots plus the duration of one
space between consecutive dots or dashes.

Output Interface:

Transmitter keying transistor may be used for

either cathode or gridblock keying (but not both
simultaneously).

Transistor ratings:

Cathode keying:

Voltage, nonconducting:
+250 V DC
Current, conducting: 150 mA DC

Grid-block keying:

Voltage, nonconducting:
–150 V DC

Current, conducting: –150 mA DC

Output power rating: 1 Watt

Morse Keyfunctions:
10 numeric (0 through 9)

26 alphabetic (A through Z)
9 punctuation marks:

      . , : ; / " - ' ()
   5 special character keys:
      (SK, AS, AR, KN, BT)
   2 shift keys

1 break (tune) key

1 error key (8 dots)

2 three-character memory keys:
(CQ and AUX)

1 identifier key (HERE IS)
1 space bar

All RTTY-only keys produce the Morse error signal.

Sidetone Oscillator:

Internal speaker emits audio tone keyed in

synchronism with output keying transistor.

Volume adjustable by panel control. Pitch
adjustable by internal control.

Identifier:

Performs same function as in RTTY mode.

Character Buffer Memory:

Performs same function as in RTTY mode.

N-Key Rollover:

Performs same function as in RTTY mode.

General:

Size: 13.5" wide, 5" high, 9" deep
(34.3 × 12.7 × 22.9 cm)

Weight: 5 lbs. (2.27 kg.)

Power:

105 - 125 V AC, 47 to 440 Hz, 1/8 amp. (Optional
220 - 250 V AC, 1/16 amp).

Operating Temperature:

50 to 95 °F (10 to 35 °C).

«
...
5
6
7
8
9
...
»

Содержание DKB-2010






































































































Отзывы:

Нет отзывов