Hal Communications DKB-2010 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 101

Hal Communications DKB-2010 Скачать руководство пользователя страница 12

10

2.4 RTTY Loop Connections

Since the RTTY output stage of the keyboard is isolated from ground and from the chassis, the keyboard

can be connected at any convenient point in the station loop circuit, provided that the voltage from either
loop connection to ground does not exceed 250 volts. Loop current is switched by a transistor, rated to carry
up to 80 mA DC and to withstand loop voltages up to 250 volts DC. Before making any connections to the

keyboard, measure the loop voltage in the space condition and the current during mark pulses to make

certain that neither exceeds the keyboard ratings.

UNPLUG THE KEYBOARD AND THE STATION LOOP SUPPLY BEFORE TAKING ANY

CONNECTIONS.

A typical station loop circuit is shown in Figure 2.3. A 6 pin plug is used to connect the loop to the

keyboard. Break the loop circuit at the desired point and connect the positive lead to pin 1 of the plug.
Connect the negative lead to pin 3. The cable shield, if one is used, may be connected to pin 2. A jumper
(or additional RTTY equipment) should be connected between pins 4 and 6. Double check the polarity of the

loop leads, as reverse voltages may damage the switching transistor. Then insert the plug into the RTTY

LOOP jack on the keyboard rear panel.

If the negative loop keying lead is grounded, the connections shown in Figure 2.4 should be used.

Prepare the plug connections as shown in Figure 2.4A.

«
...
10
11
12
13
14
...
»

Содержание DKB-2010






































































































Отзывы:

Нет отзывов