Hal Communications DKB-2010 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 101

Hal Communications DKB-2010 Скачать руководство пользователя страница 6

4

DKB-2010 SPECIFICATIONS

RTTY MODE

Code:

International Teletype, Baudot

Character Format:

1 start bit (space)

5 data bits (mark or space)

1.5 stop bits (mark)

The duration of each bit is one select time,

determined by the transmission rate. The minimum

stop bit length for Baudot code ranges from 1 to
1.46 bits, depending on transmission rate and
application.

Data Sense:

Mark or "1": holding condition, output con-

ducting.
Space or "0": signaling condition, output noncon-

ducting.

Character Transmission Rates:
60 words per minute, 45.45 baud.
Select time: 22 msec.

   66 words per minute, 50.0 baud.
      Select time:  20 msec.
   75 words per minute, 56.9 baud.
      Select time:  17.57 msec.

100 words per minute, 73.7 baud.

Select time: 13.47 msec.

Also available on special order:
132 words per minute, 100 baud
Select time: 10 msec.

Transmission Rate Accuracy:

Crystal controlled to within ± .05 % for ambient
temperatures from 50 to 95 °F (10 to 35 °C).

Output Interface:

Isolated loop switching transistor.
Ratings:
Voltage, nonconducting: 250 V DC

Current, conducting: 80 mA DC

Isolation voltage rating:
Either loop connection to chassis and ground 250
V AC or DC.

Output Power Rating: 1 Watt.

RTTY Keyfunctions:
10 numeric (0 through 9)

   26 alphabetic (A through Z)
   15 punctuation marks:
      . , : ; / " - ! " # & $ () '
   3 carriage control keys: linefeed

carriage return, and blank

2 shift keys

1 break key
2 manual case-change keys

2 three-character memory keys (CQ and AUX)
(repeating)

      Unless otherwise requested, AUX key transmits
       "DX" plus a space.
   1 identifier key (HERE IS) (repeating)
   1 test message key (QBF: "quick brown fox")

(repeating)

1 space bar

Identifier:

Transmits  the  letters  "DE"  followed  by  the  pre-
programmed  station  call  sign  of  up  to  12
characters  when  the  HERE  IS  key  is  struck.
Message repeats as long as key is held down.

Test Message Generator:

Transmits the message "THE QUICK BROWN FOX
JUMPS OVER THE LAZY DOG'S BACK
Ø123456789" when the QBF key is struck.

Repeats if key is held down.

End-of-Line Warning:

Panel lamp lights and audio tone burst is emitted
if more than 64 printing characters are trans-
mitted without an intervening carriage return.

Character Buffer Memory:

Stores up to three characters if typing speed
exceeds character transmission rate. Panel lamp

warns when memory is full. Optional 64 and 128
character buffers are available.

N-Key Rollover:

New key may be pressed before the preceding

key is released.

Automatic Case Shift:

Numbers may be transmitted without use of the
shift key; case shift codes are transmitted auto-

matically.

«
...
4
5
6
7
8
...
»

Содержание DKB-2010






































































































Отзывы:

Нет отзывов