manualshive.com logo in svg

Hal Communications DKB-2010, Инструкция по эксплуатации, Страница: 16 / 101

Поделиться
Скачать
Hal Communications DKB-2010 Скачать руководство пользователя страница 16

14

Figure  3.1     Location of Controls and Keys

As soon as you type the first character of a series, the keyboard will begin transmitting it. You may then

type two more characters, even though transmission of the first one has not been completed. The keyboard
will "remember" characters and transmit them in the proper sequence. To help you pace your typing, the

MEMORY FULL lamp will light when three characters have been stored. Simply wait until the light goes out,

indicating that there is room for another character in the memory, before your next keystroke. If you should
happen to press another key while the memory light is on, the last character in the memory will be replaced

with the new one typed.

The n-key rollover feature means that you do not have to release a key before striking the next one. The

keyboard will transmit the characters in the proper order.

Another  operating  convenience  of  the  keyboard  is  the  Line  length  indicator.  If  you  type  more  than  64

consecutive  printing  characters,  the  END  OF  LINE  lamp  will  light  and  an  audio  tone  will  be  emitted  as  a
reminder to send a carriage return and linefeed. Non-printing characters, such as Linefeeds and blanks, are
not counted as part of the 64 characters, This warning feature is particularly useful when you are punching
paper tape.

Five  standard  RTTY  control  keys  are  provided.  The  LINEFEED,  RETURN  (carriage  return),  and  BLANK

keys perform their normal functions of advancing the printer paper one line, returning the carriage to the
left margin, and punching blank characters on paper tape, respectively. Although the keyboard produces all
required figures-case and letters-case codes automatically, a figures (FIGS) key and letters (LTRS) key are
provided  so  that  you  may  manually  shift  the  case  of  the  receiving  teleprinter.  It  is  not  necessary  to  use

these keys when transmitting characters which appear on the upper half of the keytops. Instead, use one of
the SHIFT keys as described previously. The keyboard will automatically transmit the figures-case code, and
will also return the printer to letters case the next time a letter key is struck.

The  keyboard  includes  a  number  of  special  keys  which  simplify  RTTY  operation  by  automatically

transmitting strings of several characters at a single keystroke. The key labeled QBF produces the standard

RTTY  test  signal:  "THE  QUICK  BROWN  FOX  JUMPS  OVER  THE  LAZY  DOG'S  BACK  Ø123456789".  It  is  not
necessary to hold the key down once the message has started. If, however, the key is held down through
the end of the sequence, the entire message will be repeated.

A station identifier, actuated by the HERE IS key, is preprogrammed to transmit the letters "DE", followed

by your station call sign. The sequence will be repeated as long as the key is held down.

The  CQ  key  produces  the  letters  "CQ"  followed  by  a  space.  Another  special  key,  labeled  AUX  (for

auxiliary)  can  be  preprogrammed  to  transmit  any  group  of  three  characters.  On  factory-assembled
keyboards, this key is programmed with the characters requested by the purchaser when the keyboard was

ordered. If not specified, it is programmed to produce the letters "DX" followed by a space. Kit builders may
select the characters at the time of construction. Both keys repeat their character sequence if held down.

Содержание DKB-2010






































































































Отзывы:

Нет отзывов