manualshive.com logo in svg

hager HZI855, Инструкция по эксплуатации, Страница: 56 / 65

Поделиться
Скачать
hager HZI855 Скачать руководство пользователя страница 56

6LE007317A

56

13.4. Annex IV: Outputs list

These options can be configured in the Parameters / I/O / Inputs menu:

Trigram

Output name

Description

PO1

POS 1 ORDER

Switch position order to go to Source 1

PO2

POS 2 ORDER

Switch position order to go to Source 2

PO0

POS 0 ORDER

Switch position order to go to Source 0

PA0

POS 0 ORDER S1

Switch position order to go to center-off (source 1)

PB0

POS 0 ORDER S2

Switch position order to go to center-off (source 2)

S1A

S1 AVAILABLE

Source 1 available:

Output activated if source 1 is considered as available (see conditions of availability in the dedicated chapter of 

the manual).

S2A

S2 AVAILABLE

Source 2 available:

Output activated if source 2 is considered as available (see conditions of availability in the dedicated chapter of 

the manual).

SCA

ANY SOURCE AVAIL

Source 1 OR source 2 available:

This output is activated when at least one source (S1 or S2) is available.

S1U

S1 UNAVAIL

Source 1 unavailable:

Output activated if source 1 is not considered as available (see conditions of availability in the dedicated 

chapter of the manual) or the source has been inhibited.

S2U

S2 UNAVAIL

Source 2 unavailable:

Output activated if source 2 is not considered as available (see conditions of availability in the dedicated 

chapter of the manual) or the source has been inhibited.

AC1

S1 CLOSED

Source 1 closed:

This output has the function of an auxiliary contact. When the controller has the input from the switch to be 

in source 1, the output will be active. This also considers the case where with no real information about the 

position, the controller works in blind mode.

AC2

S2 CLOSED

Source 2 closed:

This output has the function of an auxiliary contact. When the controller has the input from the switch to be 

in source 2, the output will be active. This also considers the case where with no real information about the 

position, the controller works in blind mode.

AC0

OFF POSITION

Both sources open (center-off):

This output has the function of an auxiliary contact. When the controller has the input from the switch to be in 

center-off, with both switches open, the output will be active. This also considers the case where with no real 

information about the position, the controller works in blind mode.

FLT

FAULTS ACTIVE

At least 1 fault is active on the controller. Fault report

ROS

(EXT) TEST ON LOAD

This output is activated if any load test (either HMI or remote order) is ongoing.

ARO

CRIT. ALM. ACTIVE

This alarm output will be active in the case that one of the alarms set in the Alarms menu is active and the 

option to use the output to report the alarm is enabled.

-

NONE

OUTPUT NOT USED

GS1

GENSET S1 START

Genset start/stop output. Only available on OUT 5 when the source is a generator (when configured as Genset/

Genset) or on OUT 6 (when configured as Main/Genset with priority on S2).

GS2

GENSET S2 START

Genset start/stop output. Only available on OUT 6 when the source is a generator.

Position orders should not be used with the OUT 5 and 

OUT 6 (latching relays).

The latching relays can take up to 2 seconds between 

opposite orders (NO to NC or NC to NO) and for added 

security when starting a genset will change state based 

on the timers or when the backup power is exhausted.

Содержание HZI855


































































Отзывы:

Нет отзывов