manualshive.com logo in svg

hager HZI855, Инструкция по эксплуатации, Страница: 40 / 65

Поделиться
Скачать
hager HZI855 Скачать руководство пользователя страница 40

6LE007317A

40

11.1.5. COMMUNICATION parameters menu

RS485

The MODBUS RTU protocol available on the HZI855 communicates via an RS485 series link (2 or 3 wires) which is used to operate, 

configure or read parameters from a PC or an API.
In a standard configuration, a RS485 connection is used to connect 32 products to a PC or a controller up to 1200metres (1300yds) far.

N 1 

N 2 

N n 

1200 M

R = 120 Ω

Gateway, EMS,

BMS, DCIM,

SCADA, PLC...

A LIYCY shielded twisted pair must be used. We recommend using HTG485H (25m Modbus cable), a shielded twisted pair with a 

general LIYCY-CY shielding in a environment where there is interference or in a very long network with a number of products.

If the distance of 1200 m is exceeded and/or the number of products is greater than 32, a repeater must be added to enable 

additional products to be connected. 

A 120 Ohm resistor must be fixed at both ends of the connection.

N 1 

repeater

RS485

+ -    - + 

N n 

R = 120 Ω

max 1200 M ou 32 UL

max 1200 M ou 32 UL

R = 120 Ω

R = 120 Ω

Gateway, EMS,

BMS, DCIM,

SCADA, PLC...

Communication tables: can be found on the website at the following address:

 

http://hgr.io/r/hzi855

Содержание HZI855


































































Отзывы:

Нет отзывов