manualshive.com logo in svg

hager HZI855, Инструкция по эксплуатации, Страница: 51 / 65

Поделиться
Скачать
hager HZI855 Скачать руководство пользователя страница 51

6LE007317A

51

Note: indicated references are used for MCCB x250/P250 and x630/P630.

Default configuration for Inputs and Outputs for "Breaker" mode:

IN1: Breaker 1 is in position ON

IN2: Breaker 2 is in position ON

IN3: Breaker 1 is in position OFF

IN4: Breaker 2 is in position OFF

IN5: Breaker 1 is in position TRIP

IN6: Emergency stop

OUT1: Order to close Breaker 1

OUT2: Order to close Breaker 2

OUT3: Order to open Breaker 1

OUT4: Order to open Breaker 2

OUT5: NONE

OUT6: Order to start Genset

This configuration is defined with source 1 as the priority source.

This diagram covers most application cases, the inputs and outputs 

are configured by default for this installation, the actions of the 

controller will be:

-   In the event of neutral loss from source 1: the undervoltage coil will 

trip the circuit breaker for source 1 making it unavailable (ALarm 

contact on input 5) to switch to secondary source 2.

-   In the event of tripping via the emergency stop button: the 

undervoltage coil will trip the circuit breaker of the source 1 making 

it unavailable (ALarm contact on input 5) BUT the controller will 

switch to " total inhibition ”(input 6 activated), that is to say that the 

load will no longer be supplied without manual intervention on the 

controller in order to acknowledge this fault.

After acknowledgment, the controller will switch to priority source 1 if 

available, otherwise to secondary source 2.

HZI855 with MCCB

for network / network application type

for network / genset application type

 

 
 

HXA021H

AX contact

230 Vac

HXA014H

UV coil

230 Vac

4

 2

1

1

HXA021H

AX contact

230 Vac

2 

4

1

HXA024H

AL contact

230 Vac

2 

4

HXA014H

UV coil

230 Vac

 
 

mechanical

interlock

HX

x

042H

MCCB 1

MCCB 2

P1 OFF ON C P2 E

Motor 1

230 Vac

supply

electrical

interlock

11 14 12

21 24 22

31 34 32

41 44 42

51 54 52

61 64 62

71 72 73 74 75 76 70 82 81

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

USB

IN1 IN2 IN3 IN4 IN5 IN6 COM + -

INPUTS

N

SOURCE 1 

    L3  

  

L2     L1

N

SOURCE 2 

    L3  

  

L2     L1

RS485

NC - +

HX

x

042H

P1 OFF ON C P2 E

Motor 2

230 Vac

supply

ESC427

ESC126

1

1

2

L1
L2
L3
N

L1
L2
L3
N

230/400 V

230/400 V

emergency

stop

1 A

1 A

ESC427

ESC427

6 A

6 A

2

 

 
 

HXA021H

AX contact

230 Vac

HXA014H

UV coil

230 Vac

4

 2

1

1

HXA021H

AX contact

230 Vac

2 

4

1

HXA024H

AL contact

230 Vac

2 

4

HXA014H

UV coil

230 Vac

 
 

mechanical

interlock

HX

x

042H

MCCB 1

MCCB 2

P1 OFF ON C P2 E

Motor 1

230 Vac

supply

electrical

interlock

11 14 12

21 24 22

31 34 32

41 44 42

51 54 52

61 64 62

71 72 73 74 75 76 70 82 81

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

USB

IN1 IN2 IN3 IN4 IN5 IN6 COM + -

INPUTS

N

SOURCE 1 

    L3  

  

L2     L1

N

SOURCE 2 

    L3  

  

L2     L1

RS485

NC - +

HX

x

042H

P1 OFF ON C P2 E

Motor 2

230 Vac

supply

1

1

2

L1
L2
L3
N

L1
L2
L3
N

230/400 V

230/400 V

emergency

stop

1 A

1 A

ESC427

ESC427

GE

Start 

6 A

6 A

Содержание HZI855


































































Отзывы:

Нет отзывов