Grizzly G0634Z insert Скачать руководство пользователя | Manualshive

Страница: 31 / 92

background image

Model G0634Z/G0634XP (Mfd. Since 01/20)

-17-

Extension Cords

We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.

Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:

Minimum Gauge Size ...........................10 AWG

Maximum Length (Shorter is Better).......50 ft.

Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.

Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

Grounding Instructions

This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.

The power cord and plug specified under “Circuit
Requirements  for  220V”  on  the  previous  page
has an equipment-grounding wire and a ground-
ing  prong.  The  plug  must  only  be  inserted  into
a  matching  receptacle  (outlet)  that  is  properly
installed  and  grounded  in  accordance  with  all
local codes and ordinances (see figure below).

No adapter should be used with plug. If

plug does not fit available receptacle, or if

machine must be reconnected for use on a

different type of circuit, reconnection must

be performed by an electrician or qualified

service personnel, and it must comply with

all local codes and ordinances.

Figure 14.

Typical L6-30 plug and receptacle.

Grounding Prong

is Hooked

Current Carrying Prongs

L6-30 GROUNDED

LOCKING

RECEPTACLE

L6-30

LOCKING

PLUG

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

«
...
29
30
31
32
33
...
»

Содержание G0634Z insert





























































































Отзывы:

Нет отзывов

Похожие инструкции для G0634Z insert

Бренд: Enabling Devices Страницы: 2

Бренд: SYNOS Страницы: 19

Бренд: Telefunken Страницы: 20

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 4

Бренд: Sony Страницы: 12

Бренд: Sony Страницы: 56

Бренд: Sony Страницы: 37

Бренд: Naxa Страницы: 22

Бренд: Electron Страницы: 7

Бренд: Jet Страницы: 36

Бренд: MPMan Страницы: 55

CD One-Signature

Бренд: METRONOME TECHNOLOGIE Страницы: 18

Бренд: Durabrand Страницы: 17

Бренд: SONNETEER Страницы: 7

Бренд: Harman Kardon Страницы: 3

Бренд: Yamaha Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды