Grizzly G0634Z insert Скачать руководство пользователя

Страница: 19 / 92

Model G0634Z/G0634XP (Mfd. Since 01/20)

-5-

N. Fence Lock Lever:

Tightens to secure lateral

fence position along width of tables; loosens

to allow adjustment.

O. Fence Tilt Lock:

Tightens to secure fence tilt

setting at desired angle; loosens to allow tilt

adjustment.

P. 90° Fence Stop:

Allows fence to be quickly

positioned at 90° when adjusting tilt setting.

Q. Fence Tilt Scale:

Indicates angle of fence tilt

adjustment.

Jointer Fence Controls (G0634Z)

Jointer Fence Controls (G0634XP)

Figure 7.

Location of 45° fence stop (G0634XP).

R. 45° Fence Stop:

Allows fence to be quickly

positioned at 45° when adjusting tilt setting.

H. Fence Adjustment Knob:

Rotates to adjust

lateral position of fence along width of jointer

tables.

I. Fence Lock Lever:

Tightens to secure fence

position along width of tables; loosens to

allow adjustment.

J. Fence Height Lock Knobs:

Tighten to

secure fence height after tilt adjustment;

loosen to allow adjustment.

K. Fence Tilt Lock:

Tightens to secure fence

tilt setting at desired angle; loosens to allow

adjustment.

Figure 4.

Locations of fence controls (G0634Z).

Figure 5.

Location of fence tilt scale (G0634Z).

Figure 6.

Locations of jointer fence controls

(G0634XP).

L. Fence Tilt Scale:

Indicates angle of fence tilt

adjustment.

M. Fence Stops:

Allow fence to be quickly

positioned at 45° or 90° when adjusting tilt

setting.

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды