Grizzly G0634Z insert Скачать руководство пользователя | Manualshive

Страница: 74 / 92

background image

-60-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Adjusting Roller

Spring Tension

Roller spring tension must be adjusted so that

feed roller pressure is uniform. Roller spring ten-

sion will vary, depending on the type of wood you

plane.

Less spring tension is generally more forgiving on

workpieces. Therefore, if you plane milled lumber

with consistent surface heights, less spring ten-

sion is required. Likewise, if you plane rough lum-

ber with inconsistent surface heights, more spring

tension is required to keep the workpiece feeding

through the planer without stopping.

Items Needed:

Qty

Hex Wrench 6mm .............................................. 1

To adjust feed roller spring tension:

1.

DISCONNECT MACHINE FROM POWER!

2.

Adjust tension screws shown in

Figure 89

counterclockwise so that they are five to

seven turns below top of head casting.

— If workpiece slips when you feed it, turn

screws

1

⁄

2

to 1 turn counterclockwise to

increase spring tension.

— If workpiece is abruptly grabbed when

initially fed into planer, turn screws

1

⁄

2

to 1

turn clockwise to decrease spring tension.

Figure 89

. Spring tension screws.

Tension

Screws

Anti-Kickback

Fingers

Figure 90.

Location of anti-kickback fingers.

Anti-Kickback Fingers

The anti-kickback fingers are an important safety
feature of your planer. The fingers hang from a rod
suspended across the head casting and in front of
the infeed roller, as shown. This design allows the
workpiece to easily enter the planer but reduces
the risk of kickback by digging into the workpiece
if it moves backward.

Check the anti-kickback fingers regularly to ensure
they swing freely and easily. If the fingers do not
swing freely and easily, first clean them with a
wood-resin solvent, then inspect them for dam-
age. If any of the fingers are damaged, the device
must be replaced before using the machine.

Do not apply oil or other lubricants to the anti-kick-
back fingers that will attract dust and restrict free
movement of the fingers.

Proper operation of anti-kickback fingers

is critical for safe operation of this planer.

DO NOT operate planer if anti-kickback

fingers are not operating correctly. Failure

to heed this warning could result in serious

personal injury.

«
...
72
73
74
75
76
...
»

Содержание G0634Z insert





























































































Отзывы:

Нет отзывов

Похожие инструкции для G0634Z insert

Бренд: Enabling Devices Страницы: 2

Бренд: Denon Страницы: 2

Бренд: Madison Страницы: 52

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 5

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 9

Бренд: Philips Страницы: 11

Бренд: Philips Страницы: 12

Бренд: Philips Страницы: 13

Бренд: Philips Страницы: 13

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 16

Бренд: Philips Страницы: 16

Бренд: Philips Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды