Grizzly G0634Z insert Скачать руководство пользователя страница 65

Страница: 65 / 92

Model G0634Z/G0634XP (Mfd. Since 01/20)

-51-

Try to fit a feeler gauge or combination of

feeler gauges 0.062" to 0.069" between the

bottom of the ruler and the cutterhead body

as shown in

Figure 68

— If the feeler gauge slides with slight resis-

tance between the ruler and cutterhead

and no gaps appear, go to

Step 5

— If the feeler gauge does not slide with

slight resistance between the ruler and

cutterhead, or if gaps appear, go to

Correcting Outfeed Table Parallelism

Page 52

before proceeding to

Step 5.

Checking/Adjusting

Jointer Table

Parallelism

The outfeed table is preset by the factory parallel

with the cutterhead. However, it is critical to check

this setting. If the tables are not parallel with the

cutterhead or each other, then poor cutting results

and kickback can occur.

Items Needed

Qty

Straightedge ...................................................... 1

Adjustable Wrench ........................................... 1

Heavy Leather Gloves (Pair) ............................. 1

Feeler Gauge Set .............................................. 1

Checking Outfeed Table Parallelism

DISCONNECT MACHINE FROM POWER!

Put on heavy leather gloves, then remove the

cutterhead guard and fence.

Place the straightedge on the outfeed table

so it hangs over the cutterhead in one of the

positions shown in

Figure 67

Black Lines Represent
Straightedge Positions
From Overhead View

Figure 67.

Straightedge positions for verifying if

outfeed table is parallel with cutterhead.

Straightedge

Outfeed Table

0.062" (

⁄

Feeler Gauge

Figure 68.

Using feeler gauge to check outfeed

table cutterhead height.

Continue placing the straightedge in the

remaining positions shown in

Figure 67

. In

each position, the feeler gauge measurement

should be nearly identical.

— If the outfeed table height above the

cutterhead is equal across the table in

each position, then the outfeed table is

already parallel with the cutterhead. Go to

Checking Infeed Table Parallelism,

Page 52

— If the outfeed table height is not equal

across the table in any of the positions,

then the outfeed table is not parallel with

the cutterhead. Correct the outfeed table

parallelism, then correct the infeed table

parallelism.

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды