Grizzly G0634Z insert Скачать руководство пользователя страница 38

Страница: 38 / 92

-24-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Setting Outfeed

Table Height

The outfeed table height MUST be level with the

carbide inserts when they are at top-dead-center.

If the outfeed table is set too low, the workpiece

will be tapered from front to back. If the outfeed

table is set too high, the workpiece will hit

the edge of the outfeed table during operation,

increasing the chance of kickback.

To set the outfeed table height:

DISCONNECT MACHINE FROM POWER!

Place a straightedge on the outfeed table so

it extends over the cutterhead

Open the motor access panel and rotate the

cutterhead pulley until one of the carbide

inserts is at top-dead-center (TDC), as illus-

trated in

Figure 22

Figure 22.

Carbide insert at top-dead-center.

Bottom Dead

Center

Top Dead

Center

Raise or lower the outfeed table until the

carbide insert just touches the straightedge

(

Figure 23

Figure 23.

Using a straightedge to align outfeed

table height with carbide insert at TDC.

Straightedge

Outfeed

Infeed

Assembly

Models G0634Z and G0634XP come fully assem-

bled except for installation of the cutterhead

guard (see

Figure 21)

. The cutterhead guard

helps to protect hands and fingers from the rotat-

ing cutterhead during jointing operations. The

cutterhead guard MUST be installed before oper-

ating this machine.

To install the cutterhead guard:

Remove the shaft lock knob and insert the

cutterhead guard shaft into the bracket hole

as shown in

Figure 21

Move the fence forward until it touches the

cutterhead guard.

Thread the lock knob into the bracket so

the threads fit into the shaft groove (see

Figure 21

), and secure the guard into place.

Adjust the guard and lock knob as needed so

the guard fully covers the cutterhead.

Test the guard by pulling it back and letting

go. The rubber bumper on the guard should

hit the fence when the guard comes back.

— Guard should snap back over cutterhead

without dragging across table.

— If guard drags across table, raise it until it

won't drag, then tighten shaft lock.

— If guard does not snap back, remove it and

repeat

Steps 1–3

Figure 21

. Installing cutterhead guard.

Groove

Bracket

Shaft Lock

Knob

Removed

Cutterhead

Guard

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды