Grizzly G0634Z insert Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 92

background image

-36-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Bevel Cutting On

Jointer

To bevel cut on jointer:

1. Inspect stock to ensure it is safe and suitable

for the operation

(see Stock Inspection &

Requirements section).

2. Set infeed table height to cutting depth

desired for each pass.

CAUTION: Cutting depth for bevel cuts is

typically between

1

⁄

16

" and

1

⁄

8

", depending on

hardness and width of stock.

3. Set fence tilt to desired angle of cut.

4. Place workpiece against fence and infeed

table with concave side face down.

5. Start jointer.

6. With a push block in your leading hand, press

workpiece against table and fence with firm
pressure, and feed workpiece over cutter-
head with a push block in your trailing hand.

CAUTION: When your leading hand gets

within 4" of the cutterhead, lift it up and over
cutterhead, and place push block on portion
of the workpiece once it is 4" past cutterhead.
Now,  focus  your  pressure  on  outfeed  end
of  the  workpiece  while  feeding,  and  repeat
same  action  with  your  trailing  hand  when  it
gets  within  4"  of  cutterhead.  To  help  keep
your hands safe, DO NOT let them get closer
than 4" from moving cutterhead at any time
during operation!

7. Repeat cutting process, as necessary, until

you are satisfied with the results.

NOTICE

If you are not experienced with a jointer,

set depth of cut to 0", and practice feeding

workpiece across tables as described. This

will help you prepare for actual operations.

Figure 36.

Example photo of fence setup for a

bevel cut of 45°.

Removed

Surface

Bevel cuts (see example

Figures below) can be

made  by  setting  the  fence  at  the  desired  angle
and feeding the workpiece firmly along the fence
face, with the bottom inside corner firmly against
the  table.  The  cutting  process  typically  requires
multiple  passes  or  cuts  to  bevel  the  entire  edge
of a workpiece.

«
...
48
49
50
51
52
...
»

Содержание G0634Z insert





























































































Отзывы:

Нет отзывов

Похожие инструкции для G0634Z insert

Бренд: Magnavox Страницы: 30

Бренд: Magnavox Страницы: 30

Бренд: Craig Страницы: 23

Бренд: Lenoxx Страницы: 14

Бренд: Lenoxx Страницы: 24

Бренд: Lenoxx Страницы: 26

Бренд: Makita Страницы: 20

Бренд: Sherwood Страницы: 20

Бренд: Sherwood Страницы: 26

Бренд: ALDI Страницы: 28

PLANER PAL W1226

Бренд: Woodstock Страницы: 2

WJ-NX510K Series

Бренд: i-PRO Страницы: 22

Бренд: Konig Страницы: 63

Бренд: DAS Страницы: 11

Бренд: Magnavox Страницы: 16

Бренд: Parasound Страницы: 8

Бренд: Tascam Страницы: 216

Бренд: Emerson Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды