Grizzly G0634Z insert Скачать руководство пользователя

Страница: 62 / 92

-48-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Tensioning/

Replacing V-Belts

Two V-belts transfer power from the motor to the

cutterhead. To ensure efficient transfer of power

to this system, make sure the V-belts are always

properly tensioned and in good condition.

Note

After the first 16 hours of belt life, re-tension

the belts, as they will stretch and seat during this
time.

If the V-belts are worn, cracked, or damaged,

replace them. Always replace the V-belts with a

matched set of two, or belt tension may not be

equal among the belts, causing premature belt

failure.

Consider replacing stock belts with Power Twist

V-belts (see

Page 41

) to reduce vibration and

noise, and increase belt lifespan.

Items Needed

Qty

Wrench or Socket 10, 12, 14mm .................1 Ea.

2 x 4 (Length as Needed) ................................. 1

To reduce risk of shock or

accidental startup, always

disconnect machine from

power before adjustments,

maintenance, or service.

Tensioning V-Belts

DISCONNECT MACHINE FROM POWER!

Remove motor access panel on back of

machine (see

Figure 59

Note:

A collection of black belt dust inside the

motor compartment is normal during the life
of the belts.

Figure 59

. Location of V-belts and belt tension

knob.

Figure 60

. Checking V-belt tension.

Pulley

Deflection

Pulley

⁄

–1

⁄

Press each belt with moderate pressure

in center to check belt tension. Belt is cor-

rectly tensioned when there is approximately

⁄

"–

⁄

" deflection when pushed, as shown in

Figure 60

V-Belts

Motor Access

Panel Removed

Use belt tension knob (see

Figure 59

) to

adjust V-belt tension until there is approxi-

mately

⁄

"–

⁄

deflection when V-belts are

pushed with moderate pressure, as shown in

Figure 60.

Reinstall motor access panel.

Belt

Tension

Knob

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды