Grizzly G0634Z insert Скачать руководство пользователя страница 69

Страница: 69 / 92

Model G0634Z/G0634XP (Mfd. Since 01/20)

-55-

Replacing Carbide

Inserts

Items Needed:

Qty

T-Handle Wrench w/T-20 Torx Bit ..................... 1

The cutterhead is equipped with 56 indexable car-

bide inserts. Each insert can be rotated to reveal

any one of its four cutting edges. Therefore, if

one cutting edge becomes dull or damaged,

simply rotate it 90˚ to reveal a fresh cutting

edge (

Figure 79

Figure 79.

Insert rotating sequence.

Reference Dot

In addition, each insert has a reference dot on

one corner. As the insert is rotated, the reference

dot location can be used as an indicator of which

edges are used and which are new. When the

reference dot revolves back around to its starting

position, the insert should be replaced.

To rotate or change a carbide insert:

DISCONNECT MACHINE FROM POWER!

Remove any sawdust from the head of the

carbide insert Torx screw.

Remove the Torx screw and carbide insert.

Clean all dust and dirt off the insert and the

cutterhead pocket from which the insert was

removed, and replace the insert so a fresh,

sharp edge is facing outward.

Note:

Proper cleaning is critical to achieving

a smooth finish. Dirt or dust trapped between
the insert and cutterhead will slightly raise the
insert, and make noticeable marks on your
workpieces the next time you plane.

Lubricate the Torx screw threads with a light

machine oil, wipe the excess oil off the

threads, and torque the Torx screw to 48-50

inch/pounds.

Note:

Excess oil may squeeze between the

insert and cutterhead, thereby lifting the insert
slightly and affecting workpiece finishes.

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды