manualshive.com logo in svg

Grizzly G0634Z insert, Руководство пользователя

Пользователи могут бесплатно загрузить руководство для производителя для Гризли G0634Z вставить с нашего сайта. Руководство поможет вам максимально эффективно использовать этот продукт и извлечь максимум пользы из него. Загрузите его сейчас с manualshive.com.

Поделиться
Скачать
background image

-14-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Additional Safety for Jointers

KICKBACK.  Occurs  when  workpiece  is  ejected 
from  machine  at  a  high  rate  of  speed.  Kickback  
injuries occur from getting struck by workpiece or 
hands being pulled into cutterhead. To reduce the 
risk of kickback, only use proper workpieces, safe 
feeding techniques, and proper machine setup or 
maintenance.

GUARD REMOVAL.  Operating  jointer  without 
guards unnecessarily exposes operator to knives/
inserts and other hazardous moving parts. Except 
when rabbeting, never operate jointer or allow it to 
be connected to power if any guards are removed. 
Turn  jointer 

OFF  and  disconnect  power  before 

clearing any shavings or sawdust from around cut-
terhead.  After  rabbeting  or  maintenance  is  com-
plete,  immediately  replace  all  guards  and  ensure 
they are properly installed/adjusted before resum-
ing regular operations.

DULL OR DAMAGED KNIVES/INSERTS. Dull or 
damaged knives/inserts increase risk of kickback 
and cause poor workpiece finish. Only use sharp, 
undamaged knives/inserts. 

OUTFEED TABLE ALIGNMENT. Setting outfeed 
table too high can cause workpiece to hit table or 
get stuck while feeding. Setting outfeed table too 
low  may  cause  workpiece  to  rock  or  shift  while 
feeding.  Both  of  these  results  will  increase  risk 
of kickback. Always keep outfeed table even with 
knives/inserts at highest point during rotation.  

INSPECTING STOCK.  Impact  injuries  or  kick-
back may result from using improper workpieces. 
Thoroughly inspect and prepare workpiece before 
cutting.  Verify  workpiece  is  free  of  nails,  staples, 
loose knots or other foreign material. Always joint 
warped workpieces with cupped side facing down.

MAXIMUM CUTTING DEPTH.  To  reduce  risk  of 
kickback, never cut deeper than 

1

⁄

8

" per pass.

GRAIN DIRECTION.  Jointing  against  the  grain 
or end grain can increase risk of kickback. It also 
requires more cutting force, which produces chat-
ter  or  excessive  chip  out.  Always  joint  or  surface 
plane WITH the grain. 

CUTTING LIMITATIONS. Cutting workpieces that 
do not meet minimum dimension requirements can 
result in kickback or accidental contact with cutter-
head. Never perform jointing, planing, or rabbeting 
cuts on pieces smaller than specified in machine 
data sheet.

PUSH BLOCKS. Push blocks reduce risk of acci-
dental cutterhead contact with hands. Always use 
push  blocks  when  planing  materials  less  than  3" 
high or wide. Never pass your hands directly over 
cutterhead without a push block. 

WORKPIECE SUPPORT.  Poor  workpiece  sup-
port or loss of workpiece control while feeding will 
increase  risk  of  kickback  or  accidental  contact 
with  cutterhead.  Support  workpiece  with  fence 
continuously during operation. Support long stock 
with auxiliary tables if necessary. 

FEED WORKPIECE PROPERLY. Kickback  or 
accidental  cutterhead  contact  may  result  if  work-
piece is fed into cutterhead the wrong way. Allow 
cutterhead  to  reach  full  speed  before  feeding. 
Never start jointer with workpiece touching cutter-
head.  Always  feed  workpiece  from  infeed  side  to 
outfeed side without stopping until cut is complete. 
Never move workpiece backwards while feeding.

SECURE KNIVES/INSERTS.  Loose  knives  or 
improperly  set  inserts  can  be  thrown  from  cutter-
head  with  dangerous  force.  Always  verify  knives/
inserts  are  secure  and  properly  adjusted  before 
operation.  Straight  knives  should  never  project 
more than 

1

⁄

8

" (0.125") from cutterhead body.

Serious cuts, amputation, entanglement, or death can occur from contact with rotating cutterhead 

or other moving components! Flying chips from cutting operations can cause eye injuries or 

blindness. Workpieces or inserts/knives thrown by cutterhead (kickback) can strike nearby 

operator or bystanders with deadly force. To reduce the risk of serious personal injury from these 

hazards, operator and bystanders MUST completely heed the hazards and warnings below.

Содержание G0634Z insert





























































































Отзывы:

Нет отзывов

Похожие инструкции для G0634Z insert

Harman Kardon HD7400 Instruction Manual preview
HD7400
Бренд: Harman Kardon Страницы: 12
Marantz CD4000/K1B Service Manual preview
CD4000/K1B
Бренд: Marantz Страницы: 28
Technics SL-MC70 Operating Instructions Manual preview
SL-MC70
Бренд: Technics Страницы: 24
Technics SC-HD310 Operating Instructions Manual preview
SC-HD310
Бренд: Technics Страницы: 28
Technics CQ-DP5EU/EC Service Manual preview
CQ-DP5EU/EC
Бренд: Technics Страницы: 53
Sony D-EJ360 - PSYC CD Walkman Specification Sheet preview
D-EJ360 - PSYC CD Walkman
Бренд: Sony Страницы: 2
Sony D-EJ360 - PSYC CD Walkman Operating Instructions preview
D-EJ360 - PSYC CD Walkman
Бренд: Sony Страницы: 2
Sony D-EJ010PS Operating Instructions preview
D-EJ010PS
Бренд: Sony Страницы: 1
Sony D-EJ1000 - Portable Cd Player Specification Sheet preview
D-EJ1000 - Portable Cd Player
Бренд: Sony Страницы: 2
Sony D-EJ010PS Marketing Specifications preview
D-EJ010PS Marketing
Бренд: Sony Страницы: 2
Sony D-EJ002 Operating Instructions preview
D-EJ002
Бренд: Sony Страницы: 2
Sony D-E771 Operating Instructions (primary manual) Operating Instructions preview
D-E771 Operating Instructions (primary manual)
Бренд: Sony Страницы: 2
Sony D-E808 Operating Instructions preview
D-E808
Бренд: Sony Страницы: 2
Sony D-E561 Primary Operating Instructions preview
D-E561 Primary
Бренд: Sony Страницы: 2
Sony D-EJ612CK - Portable Cd Player Operating Instructions Manual preview
D-EJ612CK - Portable Cd Player
Бренд: Sony Страницы: 24
Sony D-EJ616CK - Portable Cd Player Operating Instructions Manual preview
D-EJ616CK - Portable Cd Player
Бренд: Sony Страницы: 24
Sony D-EJ360 - PSYC CD Walkman Service Manual preview
D-EJ360 - PSYC CD Walkman
Бренд: Sony Страницы: 24
Sony D-E900 Operating Instructions Manual preview
D-E900
Бренд: Sony Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды