Grizzly G0634Z insert Скачать руководство пользователя

Страница: 57 / 92

Model G0634Z/G0634XP (Mfd. Since 01/20)

-43-

SECTION 6: MAINTENANCE

To reduce risk of shock or

accidental startup, always

disconnect machine from

power before adjustments,

maintenance, or service.

Schedule

For optimum performance from this machine, this

maintenance schedule must be strictly followed.

Ongoing

To maintain a low risk of injury and proper

machine operation, if you ever observe any of the

items below, shut down the machine immediately

and fix the problem before continuing operations:

• Vacuum all dust on and around the machine.

• Wipe down tables and all other unpainted

cast-iron with a metal protectant.

•

Check for/repair worn or damaged wires.

•

Check/resolve any other unsafe condition.

•

Check/tighten loose mounting hardware.

•

Check/replace damaged cutterhead knives/

inserts.

Weekly

•

Clean cutterhead.

Monthly

• Check belt for proper tension, damage, or

wear/replace belt.

• Clean/vacuum dust buildup from inside cabi-

net and off motor.

• Lubricate worm gear

• Lubricate roller chains

• Lubricate elevation lead screw

• Lubricate worm shaft

Cleaning the Model G0634Z/G0634XP is relative-

ly easy. Vacuum excess wood chips and sawdust,

and wipe off the remaining dust with a dry cloth.

If any resin has built up, use a resin dissolving

cleaner to remove it.

Protect unpainted cast-iron tables by wiping them

clean after every use—this ensures moisture

from wood dust does not remain on bare metal

surfaces. Keep the tables rust-free with regular

applications of products like G96

Gun Treatment,

SLIPIT

, or Boeshield

T-9 (see

Page 41

for more

details).

Cleaning &

Protecting

Lubrication

This machine features bearings that are lubricated

and sealed at the factory. These bearings do not

require any further attention unless they need to

be replaced. If a bearing fails, your machine will

probably develop a noticeable rumble or vibration,

which will increase when the machine is under a

load. The bearings are standard sizes and can be

replaced through Grizzly.

Follow the procedures in this section to properly

lubricate the other components, essential for long

life and trouble-free operation of your machine.

NOTICE

Failure to follow reasonable lubrication

practices as instructed in this manual for

your machine could lead to premature fail-

ure of components and void the warranty.

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды