Grizzly G0634Z insert Скачать руководство пользователя страница 40

Страница: 40 / 92

-26-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Test Run

Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.

If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The

Troubleshooting table in the

SERVICE section of this manual can help.

DO NOT start machine until all preceding

setup instructions have been performed.

Operating an improperly set up machine

may result in malfunction or unexpect-

ed results that can lead to serious injury,

death, or machine/property damage.

Serious injury or death can result from

using this machine BEFORE understanding

its controls and related safety information.

DO NOT operate, or allow others to operate,

machine until the information is understood.

To test run machine:

Clear all setup tools away from machine.

Press Emergency Stop button in.

Make sure jointer tables are folded down and

locked in place (see

Page 37

Connect machine to power by inserting power

cord plug into a matching receptacle.

Twist Emergency Stop button clockwise until

it springs out (see

Figure 26

). This resets the

switch so the machine can start.

Press ON button to turn machine

. Verify

motor starts up and runs smoothly without

any unusual problems or noises.

Press Emergency Stop button to turn machine

OFF

WITHOUT resetting Emergency Stop button,

try to start machine by pressing the ON but-

ton. The machine should not start.

— If the machine

does not

start, the safety

feature of the Emergency Stop button is

working correctly.

— If the machine

does

start, immediately

turn it

OFF

and disconnect power. The

safety feature of the Emergency Stop but-

ton is NOT working properly and must be

replaced before further using the machine.

Press ON button, then immediately press

the OFF button on the magnetic switch (see

Figure 1

Page 4

— If the machine turns

OFF

, the OFF button

is working correctly. The Test Run is com-

plete.

— If the machine does not stop, disconnect

power to the machine. The OFF but-

ton is not working correctly. This feature

must work properly and must be replaced

before further using the machine.

Figure 26.

Resetting the switch.

The Test Run consists of verifying the following:

1) The motor powers up and runs correctly,

2) the OFF button works correctly, and

3) the Emergency Stop Button works correctly.

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды