Grizzly G0634Z insert Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 92

background image

-34-

Model G0634Z/G0634XP (Mfd. Since 01/20)

To surface plane on jointer:

1. Inspect stock to ensure it is safe and suitable

for the operation

(see Stock Inspection &

Requirements section).

2. Set infeed table height to desired cutting

depth for each pass.

CAUTION: To minimize risk of kickback,

do not exceed a cutting depth of

1

⁄

16

" per pass

when surface planing.

6. Feed workpiece completely across cutter-

head while keeping it firmly against fence
and tables during the entire cut.

CAUTION: Keep hands at least 4" away

from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over cut-
terhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to con-
tinue supporting workpiece. Use push blocks
whenever practical to further reduce risk of
accidental hand contact with cutterhead.

3. Set fence to 90°.

4. Start jointer.

5. Place workpiece firmly against fence and

infeed table.

CAUTION: To ensure workpiece remains

stable during cut, concave sides of workpiece
must face toward table and fence.

7. Repeat Step 6 until entire surface is flat.

Tip: When squaring up stock, cut opposite
side of workpiece with a planer instead of the
jointer to ensure boths sides are parallel.

Surface Planing On

Jointer

Failure to use push blocks when surface

planing could result in your hands contact-

ing rotating cutterhead, which will cause

serious personal injury. ALWAYS use push

blocks when surface planing on jointer!

Figure 34.

Example surface planing operation.

Removed

Surface

The purpose of surface planing (see example

Figures below) on the jointer is to make one flat
face on a piece of stock to prepare it for thickness
planing on a planer.

«
...
46
47
48
49
50
...
»

Содержание G0634Z insert





























































































Отзывы:

Нет отзывов

Похожие инструкции для G0634Z insert

CD5I - MANUAL 2

Бренд: NAIM Страницы: 4

Бренд: MasterCraft Страницы: 14

NS-ES6113 - Micro System

Бренд: Insignia Страницы: 32

SHOP FOX W1742S insert

Бренд: Shop fox Страницы: 60

Бренд: Woodstar Страницы: 108

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды