Grizzly G0634Z insert Скачать руководство пользователя страница 68

Страница: 68 / 92

-54-

Model G0634Z/G0634XP (Mfd. Since 01/20)

Checking/Adjusting

Planer Table

Parallelism

Table Parallelism Inspection

The easiest way to check that your planer table is

parallel with the headstock is to plane a workpiece

and then measure its thickness in multiple loca-

tions. Extra care must be taken to ensure accu-

racy. If the workpiece is tapered from left-to-right

or from front-to-back, then parallelism may be a

problem. If the table is not within the maximum

allowable tolerances, it must be adjusted.

Table Parallelism Adjustments

Items Needed:

Qty

Rotacator ........................................................... 1

Wrench 12mm ................................................... 1

Hex Wrench 4, 8mm ....................................1 Ea.

To adjust the table parallelism:

DISCONNECT MACHINE FROM POWER!

Raise planer table as far as possible.

Loosen (4) cap screws on cylinder liner, as

shown in

Figure 78

Table parallelism is critical to the operation of the

planer. As such, it is essential that the planer table

is parallel with the cutterhead (within 0.002") from

side-to-side, as illustrated in

Figure 76.

Maximum Allowable Tolerances:

Cutterhead/Table Side-to-Side ..................0.002"

Head Casting/Table Front/Back ................0.020"

Figure 76.

Side-to-side parallelism of table and

cutterhead.

Cutterhead

Table

Parallel

SIDE-TO-SIDE

Table

NOT Parallel

(Front View)

Cutterhead

Figure 77.

Front-to-back parallelism.

Table

Head

Parallel

Not-Parallel

FRONT

BACK

How the planer table sits in relation to the head

casting from front-to-back is also important (see

Figure 77

). The tolerances on the front-to-back

positioning are not as critical as the cutterhead/

table side-to-side positioning. Therefore, the max-

imum allowable tolerance for the front-to-back

parallelism is not more than 0.020".

— If table is not parallel to cutterhead side-

to-side (

Figure 76

), loosen (2) lock nuts

on right or left side of cylinder liner. Adjust

set screws to raise or lower table so it is

parallel to cutterhead.

— If table is not parallel to cutterhead front-

to-back (

Figure 77

), loosen (2) lock nuts

at front or back of cylinder liner. Adjust set

screws to raise or lower front or back of

table so it is parallel to cutterhead.

Tighten (4) cap screws on cylinder liner.

Figure 78

. Adjusting table parallelism.

Lock Nut

Set Screw

Cap Screw

Cylinder

Liner

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды