Grizzly G0634Z insert Скачать руководство пользователя страница 51

Страница: 51 / 92

Model G0634Z/G0634XP (Mfd. Since 01/20)

-37-

Jointer/Planer

Conversion

Remove dust hose from jointer dust port.

Rotate infeed table lock lever (

Figure 39

)

clockwise, pull it out, and pivot table upward.

The table will lock into place when raised to

its highest position, as shown in

Figure 40

Figure 39

. Example of infeed table lock lever.

Raise outfeed table in same manner as you

did with infeed table.

Table Lock

Lever

Figure 40

. Example of infeed table pivoted up.

The Model G0634Z/G0634XP is ready for jointer

operations after it is first setup. To use the

machine as a planer, you must convert it from a

jointer to a planer.

To convert the machine for planer operations:

DISCONNECT MACHINE FROM POWER!

G0634Z:

Loosen quick release knobs (see

Figure 37

) and slide fence off of machine.

Quick-Release

Knobs

3. G0634ZXP:

Loosen fence lock lever, slide

fence toward front of machine, carefully slide

protective flap through bracket, and lift fence

off of fence rail (see

Figure 38

Figure 37

. Location of quick-release knobs

(G0634Z).

Figure 38

. Fence removal components

(G0634XP).

Fence Lock

Lever

Fence Rail

Protective Flap

Bracket

Содержание G0634Z insert





























































































Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды

Grizzly G0634Z insert, Руководство пользователя

Результаты поиска

Содержание G0634Z insert

Отзывы:

Похожие инструкции для G0634Z insert

Бренды по названию

Популярные бренды