GRAUPNER 32032, Руководство по программированию

Страница: 37 / 324

37 Transmitter description - Telemetry data display
www.graupner.de in the web page for the given
product.
RECEIVER
RX–S QUA: 100%
RX–S STR: 100%
TX–dBm: 33dBm
RX–dBm: 33dBm
RX–VOLT:4.8 TMP
L–PACK: 10ms
CH OUTPUT TYPE:ONCE R-LOW V:4.6 +22°C
This screen presents the » RX DATAVIEW « of the
Telemetry menu's » SETTING & DATAVIEW « sub-
menu, see page 229, with data processed and
displayed graphically.
The displayed items are as follows:
Value Explanation
RX-S QUA signal quality in %
RX-S ST signal strength in %
RX-dBm Reception power in dBm
TX-dBm transmit power in dBm
V PACK Indicates the longest time span in ms
in which data packages are lost in the
transmission from the transmitter to the
receiver.
RX-VOLT current operating voltage of the
receiver's power supply in volts
M-RX V Lowest receiver operating voltage since
last startup, in volts
TMP the thermometer depicts the receiver's
current operating temperature
GENERAL MODULE
RX–S QUA: 100%
RX–S ST : 100%
TX–dBm: 33dBm
RX–dBm: 33dBm
RX–SPG.:4.8 TMP
V–PACK: 10ms
CH OUTPUT TYPE:ONCE
R E C E I V E R
G E N E R A L
E L E C T . A I R
V A R I O
G P S
0.0V
BAT1
BAT2
0.0V T2 0°C
T1 0°C
E FUEL F
CELL.V
1:0.00
2:0.00
3:0.00
4:0.00
5:0.00
6:0.00
0
0.0V
BAT1
BAT2
0.0V T2 0°C
T1 0°C
E FUEL F
ALT
0m
0m1
0m3
0.0A
POWER
0.0V
0
If attached to the receiver, this screen will display the
data acquired by a General-Engine module, order no.
33610, , or a General-Air module, order no. 33611 .
More details about these modules can be found in
the appendix or in Internet at www.graupner.de in the
web page for the given product.
Depending on how this module is equipped with
sensors, this screen can permanently display the
data shown in the table below.
The current voltage of up to two batteries (BAT1
and BAT2), the measurement results of up to two
temperature sensors (T1 and T2) and a fi ll level gage
for the fuel tank.
An alternating display along the screen's right edge
will display a list of current cell voltages for a LiPo
battery with up to six cells or operational data (current
altitude with respect to the starting location, ascent/
decent m/1 s and m/3 s, current current being
drawn in amperes and current voltage of the battery
connected to the sensor).
The displayed items are as follows:
Value Explanation
BAT1 /
BAT2 battery 1 or 2
FUEL fuel level / tank gage
E / F empty / full
T1 / T2 temperature of sensor 1 or 2
CELL V cell voltage of cells 1 … max. 6
ALT current altitude
0m1 m/1 s ascent/decent rate
0m3 m/3 s ascent/decent rate
A current draw i amperes
V battery voltage
Battery and load indicators
0.0V
0.0A
0mAh
0ml
This display depicts current voltage, current current
draw and, if attached, the expended capacity of
"Batt 1" connected to the General-Engine module
(order no.
33610 ) or General-Air (order no. 33611 )
module as well as the fuel consumed in ml.