GRAUPNER 32032, Руководство по программированию

Страница: 262 / 324

262 Detail program description - Servo display
Servo display
Display of the servo position
Use the selection keys on the left or right touch pad
to scroll to the menu option »
Servo display « menu
option in the multi-function menu:
Teacher / pupil Tx. output swap
Profi trim Trim memor y
Telemetr y Channel sequence
Multichannel Ring limiter
Mp3 player Basic settings
Ser vo display Ser vo test
Briefl y tap the center SET key of the right touch pad
to open this menu option.
1
3
5
7
9
11
13
15
0
0
0
0
–100
0
0
0
–100
0
0
0
+100
0
0
0
2
4
6
8
10
12
14
16
However, the visual display of current servo positions
can not only be opened by selecting this menu, but
also – directly from the transmitter's base screen
as well as nearly all other menu positions – with a
simultaneous tap on the
ef
keys of the left touch
pad. A brief tap on the center ESC key of the left
touch pad will cause a return to the respective point
from which it was called.
The current position of each servo is displayed in a
bar diagram between -150 % and +150 % of normal
travel with consideration for the control and servo
settings, the dual-rate/expo functions, the interplay
of all active linear and curve mixers, etc. 0 %
corresponds precisely to the servo center position.
This way, you can quickly check your settings without
having to switch on the receiver. However, this does
not absolve you from fi rst carefully testing all program
steps, as well as on the model, prior to the fi rst
operation of the model in order to eliminate errors!
For winged models the display takes place
according to the following scheme:
Bar 1 = Throttle/brake servo
Bar 2 = Aileron or left aileron
Bar 3 = Elevator
Bar 4 = Rudder
Bar 5 = Right aileron
Bar 6 = Camber-changing fl ap (left) / free
channel
Bar 7 = Right camber-changing fl ap / free
channel
Bar 8 = Free channel / second elevator servo
Bar 9 = Free channel / Left FL2
Bar 10 = Free channel / Right FL2
Bar 11 = Free channel / Left AI2
Bar 12 = Free channel / Right AI2
Bar 13 = Free channel
Bar 14 = Free channel
Bar 15 = Free channel
Bar 16 = Free channel
… and for helicopter models:
Bar 1 = Pitch or roll (2) or pitch (2) servo
Bar 2 = Roll (1) servo
Bar 3 = Pitch (1) servo
Bar 4 = Tail servo (gyro)
Bar 5 = Pitch (2) servo / free channel
Bar 6 = Throttle servo or speed controller
Bar 7 = Gyro sensitivity / free channel
Bar 8 = Speed controller / free channel
Bar 9 = Free channel
Bar 10 = Free channel
Bar 11 = Free channel
Bar 12 = Free channel
Bar 13 = Free channel
Bar 14 = Free channel
Bar 15 = Free channel
Bar 16 = Free channel
Notes:
However, please note that the servo display is •
only based on the original sequence of servos.
This means that any swapping of outputs
which may have been implemented, in either
the »
Transmitter output « menu or » Receiver
output « menu, is not taken into account.
Please also note that, by default, bar diagram •
tracking is opposite to the left/right movements of
a joystick.
The number of channels shown in this menu
•
correspond to the 16 control channels available
in the
mc-20
HoTT transmitter. However, the
number of actually usable channels depends
on the receiver type as well as the number of
servos connected to it and, therefore, may be
considerably lower under certain circumstances.
Use this display during the model programming,
•
because you can immediately check all settings
on the transmitter. However, this does not absolve
you from fi rst carefully testing all program steps,
as well as on the model, prior to the fi rst operation
of the model in order to eliminate errors!