GRAUPNER 32032, Руководство по программированию

Страница: 156 / 324

156 Detail program description - Fl. phase timers
Fl. phase timers
Selecting and setting
A description of how timers are assigned to a fl ight
phase has already been provided in the text for the
»
Phase settings « menu, page 142 and 146. The
same section has also described the properties of
"Time1" and "Time2". This section now proceeds to
describe "Timer 1, 2 and 3" and the "lap counter/time
table" timer variants.
The additional, fl ight phase-specifi c timer selected
is displayed on the basic display underneath the
"center" timer, as shown below:
#01
0:00h
Stop watch
Flight tim
K78
0:00.0
4.1V
0:00.0
0 0 0 0
0:00h
M
V
Graubele
H-J Sandbrunner
Normal
Timer 1
00
0:00.0
RX VOLT:4.9V
On this menu …
Control adjust Dual Rate / Expo
Channel 1 cur ve Switch display
Control switch Logical switch
Phase settings Phase assignment
Phase trim Non-delayed chan
Timers (general) Fl. phase timers
Control adjust Dual Rate / Expo
Channel 1 cur ve Switch display
Control switch Logical switch
Phase settings Phase assignment
Non-delayed chan Timers (general)
Fl. phase timers Helicopter mixer
… you can now program "Clks 1 … 3" as stopwatches
(i.e. timers that run forward) or as countdown/alarm
timers (i.e. timers that run backwards). You can assign
any switch to these timers, and the same is true of the
"lap counter/timetable" timer:
Timer 1
Timer 2
Timer 3
Lap time/Tim tab
––– 0:00
0:00
0:00
Lap display
0s
0s
0s
–––
–––
–––
–––
Alarm Timer
The fl ight phase timers "Timer 1 … 3" and the
"Time1"/"Time2" timers (described in the »
Phase
settings « section, pp. 142 and 146) run only in the
fl ight phase to which they have been assigned. They
are also shown as appropriate on the basic display.
During other fl ight phases they are stopped (and
hidden) and the assigned stop/start switch then has
no effect.
The lap counter, once started, continues to run
through changes of phase (as discussed further
below), however, although it can be stopped during
any fl ight phase via the center
ESC key of the left
touch pad.
Clks 1, 2 and 3
These timers are started and stopped via a switch or
control switch. To do so, fi rst use the selection keys
to select the appropriate column via the switch icon
at the bottom right. Then set the switch that you want
by briefl y tapping the center
SET key of the right
touch pad, as described in the section "Assigning
transmitter controls, switches and control switches"
(p. 56). Here, too, a control switch offers you the
option of activating the timer via one of the joysticks
or proportional controls. The switching point along
the transmitter control travel is set on the »
Control
switch « menu (page 135).
Remember that the timer switches also remain active
in programming mode.
Switching between "forwards" and "backwards"
Stopwatch mode (timer runs forwards)
In this mode, the timer starts at the initial value "0:00"
(min:sec) when you operate the assigned switch. If
it reaches the maximum time of 180 min. and 59 s, it
will re-start at "0:00".
"Countdown" (timer runs backwards)
Following the activation of the corresponding value
fi elds (by tapping the center
SET key of the right
touch pad), if a time in minutes (maximum 180 min)
and/or a time in seconds (maximum 59 s, right fi eld)
is set, then the timers will run backwards from this
initial value following the activation of the assigned
switch (see section "Assigning transmitter controls,
switches and control switches" on page 56), i.e.
a "countdown" function will apply. Once the timer
reaches zero it does not stop, however, but continues
to run (highlighted) so you can read off the time
elapsed after reaching zero.
Note:
Timers that are running backwards are shown on the
basic display with a fl ashing colon (:) between the
minutes and the seconds fi elds.
A simultaneous tap on the cd or ef keys of the
right touch pad ( CLEAR ) will reset entry values in the
currently active fi eld back to zero.
"Alarm" timer
Timer 1
Timer 2
Timer 3
Lap time/Tim tab
––– 0:00
0:00
0:00
Lap display
0s
0s
0s
–––
–––
–––
–––
Alarm Timer