GRAUPNER 32032, Руководство по программированию

Страница: 78 / 324

78 Detail program description - Base setup models | Winged models
Model name
Stick mode 1
bind
B A S I C S E T T I N G , M O D E L
Info
n/a n/a Module bind
HoTT
Graubele
1234g/111111
SEL BD1 BD2 BD3 BD4
On the other hand, should the LED on the receiver
blink red for longer than about 10 seconds, the
binding process has failed. In this case the screen
will continue to show the status as "n/a". If this should
happen, try changing the position of antennas then
repeat the entire procedure.
Binding other receivers
The binding channel you have chosen is already
bound (as indicated by the "bind" status). with
another binding channel. After initiating the RF
bind process, instead of displaying "BINDING", the
message shown below appears.
Model name
Stick mode 1
geb.
B A S I C S E T T I N G , M O D E L
Info
n/a n/a Module geb. HoTT
Graubele
1234g/111111
SEL BD1 BD2 BD3 BD4
RF
off
OK
is tur ned
Drop down two lines in the screen and switch off the
RF module as described on the page in section "RF
module". Afterward, return again to the "Module" line
and restart the binding process as described above.
Alternatively, the transmitter can be switched off
briefl y then, after switching it back on again, respond
to the message window that appears …
OFF ON
Please select
RF on/off?
… with "OFF" …
ON
Please select
RF on/off?
OFF
… then confi rm the selection with a brief tap on the
center
SET key of the right touch pad. From the
base screen jump again into the "Module" line of
the »
Basic settings, model « menu and restart the
binding process.
Dissolving a bond
Proceed as described above to initiate the binding
process but WITHOUT fi rst putting a receiver in
binding readiness.
EXT. PPM
Important notice:
With the activation of the value fi eld in the context
of the following described changeover, any
existing bonds to HoTT receivers which may be
effective for the currently active model memory
will be lost.
Activate the fi rst value fi eld in the "Module" line with a
tap on the center
SET key of the right touch pad then
use the selection keys to choose "EXT. PPM" instead
of "HoTT". In parallel with the selection of "EXT.
PPM", the other four value fi elds will be replaced by
the type of modulation pre-selected in the line »DSC
Output«, see page 81.
Model name
Stick mode 1
B A S I C S E T T I N G , M O D E L
Info
Module
Graubele
1234g/111111
SEL
PPM10
EXT. PPM
This change also suppresses the lines for the options
(described below): »HoTT«, »Rcv Ch Map«, »RF
module« and »RF range test« and, in the basic
display, "PPM" will be displayed instead of "HoTT".
#01 0:00h
Stop watch
Flight tim
K78
0:00.0
4.1V
0:00.0
RX VOLT:0.0v
0 0 0 0
00:00h
M
V
PPM
Graubele
H-J Sandbrunner
Receiver channel mapping
As long as there is at least one "bound" receiver in
the "Module" line, the next line down will be the "Rcv
Ch map" line.
Model name
Stick mode 1
B A S I C S E T T I N G , M O D E L
Info
Graubele
1234g/111111
SET SET SET SET
Rcv Ch map R16 R08 n/a n/a
As mentioned in the introduction to the "Binding
receivers" section, this menu item of the
mc-20
HoTT
offers both the opportunity to freely divide up the
transmitter's control channels
within a receiver as well
as the opportunity to distribute the transmitter's 16