GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 46

Страница: 46 / 338

IQUCP Card Installation and Operation

Installation of the Optical Interface (option)

When using a double-slot-width rear panel, the card should be inserted into the right-

most of the two slots. Inserting the card into the wrong slot will not damage the card,

and will be flagged by the on-card status LED flashing red to indicate that there is no

connection to the rear panel.

3 Close the front panel of the frame.

Installation of the Optical Interface (option)

See

Installing the SFP Ethernet Module

, on page 335.

Rear Panel and Connectors

Images of Rear Panel Connectors

The rear panel is shown below, and its various inputs and outputs are described.

IQUCP2500-2B3

IQUCP2501-2B3

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды