GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 316

Страница: 316 / 338

316

Maintenance & Troubleshooting

Loading (Selecting) Software Version on the UCP

3901 / IQUCP25 / IQUCP50

4 Click

Yes

The Unit License dialog closes. When the unit has restarted the new licenses will be

active.

Loading (Selecting) Software Version on the UCP

3901 / IQUCP25 / IQUCP50

The UCP

3901 Card is a generic card and its functionality is set by the licensing that has

been enabled on it and by selecting a software version. A UCP

3901 Card may have more

than one license and software version (for example, Essence Processing and another

application).
The required functionality is selected by selecting the corresponding licensed software

version on the card.

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды