Glasair Sportsman GS-2 Скачать руководство пользователя

Страница: 123 / 216

YSTEMS

ESCRIPTIONS

EVISION

ATE

12/29/04

AGE



6-10 HEATING AND VENTILATION SYSTEMS

Optional cabin heat is provided by a heat exchanger mounted on the

exhaust system, with a heat valve mounted on the firewall. A push-pull

cable control opens and closes the cabin heat valve. If desired, the

warm cabin air can be diverted to provide windshield defrosting as well

as heating for the occupants.
Two optional cabin vents provide fresh air ventilation for the cockpit

area. NACA-style inlet ducts on both sides of the fuselage feed air into

boxes which incorporate “eyeball” vent valves to control the flow of

ventilation air into the cockpit.

6-11 ELECTRICAL SYSTEM

The electrical system is optional in the Sportsman and, thus, will vary

widely among individual Sportsmans. The only difference between the

Sportsman’s electrical system and that of more conventional aircraft is

that the composite aft fuselage structure on the Sportsman cannot be

used as a ground. Instead, a negative (ground) lead as well as a

positive (power) lead is required for any electrical equipment mounted

aft of the fuselage cage. All circuits should be protected by appropriate

circuit breakers, which can be either rocker-arm style or the standard

push-pull type.
Optional navigation/strobe light units can be mounted to the wingtip

fairings. The standard lower engine cowling has a molded recess for a

landing light lens, so an optional landing light can be easily installed.

Содержание Sportsman GS-2




































































































































































































Результаты поиска

Содержание Sportsman GS-2

Отзывы:

Похожие инструкции для Sportsman GS-2

Бренды по названию

Популярные бренды

Glasair Sportsman GS-2, Руководство пользователя

Результаты поиска

Содержание Sportsman GS-2

Отзывы:

Похожие инструкции для Sportsman GS-2

Бренды по названию

Популярные бренды