Glasair Sportsman GS-2 Скачать руководство пользователя

Страница: 164 / 216

EVISION

:
-

ATE

12/29/04

AGE



TEP

7: B

REAK

-I

N THE

RAKE

ININGS

The lining material used in the Sportsman brakes is an asbestos based

organic compound. To provide the maximum service life, the brake

lining material must be properly broken-in by gently heat curing the

resins, as described below. Excessive heat applied before curing will

carburize the lining material, lowering the braking coefficient and

reducing the service life of the linings.
To break-in the new brake lining material, perform a minimum of six

stops from a speed of between 25 and 40 m.p.h., using light pedal

effort and letting the brakes cool partially (about one minute) between

stops. This procedure generates enough heat to cure the resins in the

lining, yet will not carburize the material by heating excessively. Once

the linings are properly cured, they will provide many hours of

maintenance-free service.

7-9.4.2 Bleeding the Brakes

To bleed the brakes, use a fluid pump (such as an oil pump can) with a

clear tube attached to the brake caliper bleeder fitting. Open the

bleeder and pump fluid from the caliper through the master cylinder(s)

to the reservoir until no air bubbles are evident in the reservoir; then,

tighten the bleeder fitting. As the reservoir fills, siphon the fluid back

down into the pump or some other container to prevent overflow.

Repeat for both brake calipers until the brakes feel solid. Finally, drain
the reservoir until it is about

7/8

full.

Содержание Sportsman GS-2




































































































































































































Результаты поиска

Содержание Sportsman GS-2

Отзывы:

Похожие инструкции для Sportsman GS-2

Бренды по названию

Популярные бренды

Glasair Sportsman GS-2, Руководство пользователя

Результаты поиска

Содержание Sportsman GS-2

Отзывы:

Похожие инструкции для Sportsman GS-2

Бренды по названию

Популярные бренды