Glasair Sportsman GS-2 Скачать руководство пользователя

Страница: 169 / 216

ANDLING

, S

ERVICE AND

AINTENANCE

EVISION

ATE

12/29/04

AGE



Wash the fuselage in the same manner as the aluminum wings and tail

surfaces, and then apply a high-quality automotive paste wax to help

prevent gel coat oxidation. We recommend avoiding the use of waxes

containing silicon. Silicon is very difficult to remove from a surface,

even with solvents such as acetone, and its presence may inhibit a

good bond in the event that airframe repair or gel coat touch-up is

necessary.

7-9.9 W

INDSHIELD AND

INDOWS

Keep the windshield and door window Plexiglas clean, and wax it with

a Plexiglas polish such as Mirrorglaze. To prevent scratches, wash the

windows carefully with plenty of mild soap and water solution, using

the palm of the hand to feel and dislodge dirt and mud. A soft cloth,

chamois or sponge may be used but only to carry water to the surface.

Rinse thoroughly and then dry with a clean moist chamois. Rubbing

the surface of the plastic with a dry cloth builds up an electrostatic

charge which attracts dust particles in the air.
Remove oil and grease with a cloth moistened with isopropyl alcohol.

Never use gasoline, benzene, alcohol, acetone, carbon tetrachloride,

lacquer thinner or glass cleaner. These materials will soften the plastic

and may cause it to craze.
After a thorough cleaning, wax the surface with a good grade of

commercial wax (Mirrorglaze or similar). The wax will fill in minor

scratches and help prevent further scratching. Apply a thin, even coat

of wax and bring it to a high polish by rubbing lightly with a clean, dry,

Содержание Sportsman GS-2




































































































































































































Результаты поиска

Содержание Sportsman GS-2

Отзывы:

Похожие инструкции для Sportsman GS-2

Бренды по названию

Популярные бренды

Glasair Sportsman GS-2, Руководство пользователя

Результаты поиска

Содержание Sportsman GS-2

Отзывы:

Похожие инструкции для Sportsman GS-2

Бренды по названию

Популярные бренды