Seagull RANS S-20 RAVEN-20cc Assembly Manual Download | Manualshive

Page: 1 / 40

background image

1

A S S E M B L Y M A N U A L

RANS S-20 RAVEN

-

20cc

Specifications:

Wingspan---------------80 in (203.2 cm).
Wing area---------------1069.5 sq.in ( 69 sq.dm).
Weight-------------------12.6 lbs (5.7 kg).
Length-------------------53.4 in (135.6 cm).
Engine-------------------20cc gasoline.
Radio--------------------6 channels with 8 servos.

Code: SEA279

“ Graphics and specifications may change without notice ” .

1
2
3
...
»

Summary of Contents for RANS S-20 RAVEN-20cc









































Reviews:

No comments

Related manuals for RANS S-20 RAVEN-20cc

Brand: MicronWings Pages: 4

Brand: Technify Motors Pages: 232

Brand: SOL paragliders Pages: 39

Brand: STEMME Pages: 290

Samba R.E.S. Evo

Brand: cad2cnc Pages: 33

Brand: ICARO paragliders Pages: 22

Brand: DaVinci Pages: 37

Trango X-light2

Brand: UP Pages: 48

Brand: Piper Pages: 73

Arrow PA-28R-201

Brand: Piper Pages: 159

Brand: Piper Pages: 7

Piper Cub Trainer J3

Brand: Piper Pages: 29

Brand: Piper Pages: 34

Brand: Piper Pages: 213

Brand: Piper Pages: 499

PA-28-181 Archer II

Brand: Piper Pages: 333

Brand: Piper Pages: 846

Brand: Prism Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands