Givi Misure VISION 700 Скачать руководство пользователя страница 23

Страница: 23 / 72

10/06/2008

M042.E

•

F 28

SUM OF TWO AXES

This function can be used to perform an algebraic sum of the movements of two Carriages

moving in directions parallel one to each other: e.g. the main Carriage and the Tool

Carriage of a lathe, the Upright and the Spindle of a miller, etc...

If this function has

been activated

(decimal point flashing on the display being added up)

the operator can

“see” the true position of the tool.

If, for example, one Carriage is moving forwards and

the other is moving backwards by the same value, the count does not change (this is

because the distance between the tool and the workpiece has not changed). The

instrument is configured by the Manufacturers as required for the type of application. It

will be possible in any case to reconfigure it (ask for the access codes and procedures) if

different applications are required for use on other types of machines.

On completion of the installation, check the following:

AXIS INPUTS

(See rear panel)

MACHINE

INSTRUMENT

(In 1)

(In 2)

(In 3)

(In 4)

AXES BEING

ADDED ON
DISPLAYS:

ANY

TYPE

VI722IN

LONG.

TRANS.

ANY

TYPE

VI723IN

LONG.

Tool

Carriage

LATHE

VI723TO

TRANS.

Tool

Carriage

D MILLER

VI733IN

LONG.

TRAS.

VERT.

LATHE

VI733TO

TRANS.

Carriage

Tool

Carriage

F MILLER

VI733FR

LONG.

TRAS.

VERT.

ANY

TYPE

VI734IN

LONG.

TRAS.

VERT.

Spindle

H MILLER

VI734FV

LONG.

TRAS.

VERT.

Spindle

I MILLER

VI734FT

LONG.

TRAS.

VERT.

Saddle

BORING

MACH.

VI734AL

LONG.

TRAS.

VERT.

Spindle

NOTES:

The Axes being added up are shown in

boldface

. The other configurations

cannot be added up since the type of application does not require this.

The Axes to be added up must have the same direction of counting, the same

scale factor values and the same increment/decrement percentages, while the

linear correction factor may be different for each Axis.

The algebraic sum function may be disabled.

Содержание VISION 700









































































Результаты поиска

Содержание VISION 700

Отзывы:

Похожие инструкции для VISION 700

Бренды по названию

Популярные бренды

Givi Misure VISION 700, Инструкция по эксплуатации

Результаты поиска

Содержание VISION 700

Отзывы:

Похожие инструкции для VISION 700

Бренды по названию

Популярные бренды