Givi Misure VISION 700 Скачать руководство пользователя страница 19

Страница: 19 / 72

10/06/2008

M042.E

•

MMS/INCHES CONVERSION

Every time the following key is pressed the unit of measurement is switched from

INCHES

or vice versa. Switching takes place instantaneously for all the Axes

being counted. The selected unit of measurement is shown by the position of the LED lit

on the keypad, and also by the position of the decimal points for the Axes being counted.

If activation of the conversion is not compatible with the operational conditions of the

instrument, pressing this key will cause an error message to be displayed.

WORKPIECE CENTRE

This function makes it easy to identify the centre between two points A and B of a

workpiece being machined (distance between centres of holes, geometrical figures, sides

of the workpiece, etc.). To perform the function, for example on the Y Axis, proceed as

follows:

Go to the first position, A, by moving the Carriage along the Z

Axis.

Let us suppose that in this position the display of the Y Axis indicates

the dimension 30.00 (which it is not necessary to reset):

Key

3 0. 0 0

Both the LED of the Y Axis and the LED of the

symbol will flash on the keypad.

The auxiliary display will show the wording

“WORKPIECE CENTRE”.

Now go to the second position, B. Let us suppose that in this position the display of

the Y Axis shows the dimension 52.22

Key

1 1. 1 1

The flashing LEDs will extinguish and a dimension will appear on the display of the

Axis. This dimension is exactly half (rounded off, if necessary) of the path followed

by the Carriage between the two positions A and B. It will be sufficient to move the

Carriage as far as dimension “0.00” for it to be located exactly on the required

midpoint.

NOTE:

This function can only be carried out when the Axis concerned is set for

INCREMENTAL

counting

Otherwise it is not completed by the calculation, as

this would interfere with the

ABSOLUTE

count settings.

Содержание VISION 700









































































Результаты поиска

Содержание VISION 700

Отзывы:

Похожие инструкции для VISION 700

Бренды по названию

Популярные бренды

Givi Misure VISION 700, Инструкция по эксплуатации

Результаты поиска

Содержание VISION 700

Отзывы:

Похожие инструкции для VISION 700

Бренды по названию

Популярные бренды