GEZE TSA 160 NT F Скачать руководство пользователя

Страница: 54 / 64

TSA 160 NT

Display programme switch DPS and Service push buttons S1, S2

System messages

If one or more faults are pending, these are displayed consecutively alternatively with the current mode of

operation in encoded form with service LEDs 1 to 4.

The red LED5 flashes quickly (10 Hz) on the fault display.

The mode of operation is displayed for 5 s, the respective error message for 2 s.

Service mode

Individual parameters can be set for the control in service mode.

Within the first 3 minutes of the mains voltage being switched on, the device can be changed to service mode

using keys S1 and S2.

There is a time limit to changing to service mode using keys S1 and S2 so that safety-related parameters are

not changed unintentionally during operation.

It is possible to change from any mode of operation to the service mode.

The control automatically changes back to normal mode if no key is pressed in service mode for 3 minutes.

In service mode, the control behaves in the same way as in the OFF mode of operation, the drive does not

open and close automatically.

The door can be opened and closed manually.

Changing to the parameter selection menu

Simultaneously press keys S1 and S2 longer than 2 s.

The control changes to the parameter selection menu.

In this menu, the red LED5 flashes once (parameter level 1) or twice (parameter level 2) at 1 Hz.

The parameters are indicated in coded form by the other 4 LEDs.

The required parameters are selected using keys S1 (–) and S2 (+).

Changing to the value menu

Press key S1 for longer than 2 s.

The control changes to the value menu.

All 5 LEDs are used for coding the values.

The required value is selected using keys S1 (–) and S2 (+).

After key S1 has been kept pressed for more than 2 s the control takes over the value indicated.

Input can always be aborted by pressing key S2 for more than 2 s; the control then changes back to the value

menu or the parameter menu.

Service mode is quit by pressing keys S1 and S2 simultaneously for more than 2 s.

Display values service LEDs

Value

○ ○ ○ ○ ○

● ○ ○ ○ ○

○ ○ ○ ○ ●

● ○ ○ ○ ●

○ ○ ○ ● ○

● ○ ○ ● ○

○ ○ ○ ● ●

● ○ ○ ● ●

○ ○ ● ○ ○

● ○ ● ○ ○

○ ○ ● ○ ●

● ○ ● ○ ●

○ ○ ● ● ○

● ○ ● ● ○

○ ○ ● ● ●

● ○ ● ● ●

○ ● ○ ○ ○

● ● ○ ○ ○

○ ● ○ ○ ●

● ● ○ ○ ●

○ ● ○ ● ○

● ● ○ ● ○

○ ● ○ ● ●

● ● ○ ● ●

○ ● ● ○ ○

● ● ● ○ ○

○ ● ● ○ ●

● ● ● ○ ●

○ ● ● ● ○

● ● ● ● ○

○ ● ● ● ●

● ● ● ● ●

100

Содержание TSA 160 NT F

































































Результаты поиска

Содержание TSA 160 NT F

Отзывы:

Похожие инструкции для TSA 160 NT F

Бренды по названию

Популярные бренды

GEZE TSA 160 NT F, Схема подключения

Результаты поиска

Содержание TSA 160 NT F

Отзывы:

Похожие инструкции для TSA 160 NT F

Бренды по названию

Популярные бренды