Furuno FV-110 Скачать руководство пользователя страница 95

Страница: 95 / 240

Configuration with the web interface

5-33

• Send interval: Select disabled, day (default) with 2-minute samples, week with

hourly samples or month with hourly samples. The report contains statistics data
for the selected intervals.

4. Click

Apply.

You can also send the report at any time by clicking

Send now

. Use

Send now

to validate

the e-mail setup. See also

Download of a diagnostic report or a statistics report

page 7-2.

The following parameters are recorded in the statistics report:

Parameter recorded

Description

Hostname

Host name, entered in the web interface on the page

SETTINGS

> Network

ACU SN

ACU serial number

ADU SN

ADU serial number

SW ver.

Software version

System

FV-110

Table 5-17: Statistics report, header record

Parameter recorded

Description

UTC. (s)
UTC (YYYY-MM-DD hh:mm)

UTC in seconds and date format for the data set.

RSSI.Av
RSSI.Max
RSSI.Min

Received signal strength (average, maximum and
minimum value) for the sampling interval.

POS.Lat (degree)
POS.Long (degree)
POS.Valid

Latitude value of position.
Longitude value of position.
Fix = valid position, No Fix = invalid position.

NAV.Speed (m/s)

Navigation speed

Heading.Samp (degree)
Heading.Max (degree)
Heading.Min (degree)
Heading.Range (+/-degree)

Ship’s heading (sample, maximum and minimum
value, range) for the sampling interval. See Figure 5-
26:

Statistics — how to read data for a range

Antenna.Azi (degree)
Antenna.Azi Max (degree)
Antenna.Azi Min (degree)
Antenna.Azi Range (+/-degree)

Current antenna azimuth (sample, maximum and
minimum value, range) for the sampling interval.
See Figure 5-26:

Statistics — how to read data for a

range

Antenna.Ele (+/-degree)
Antenna.Ele Max (+/-degree)
Antenna.Ele Min (+/-degree)

Current antenna elevation (sample, maximum and
minimum value) for the sampling interval.

Table 5-18: Parameters recorded in a statistics report

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды