Furuno FV-110 Скачать руководство пользователя страница 109

Страница: 109 / 240

Keypad and menus of the ACU

5-47

5. HDG: Ship heading data received from the ship’s gyro, OK or ---.

6. LAN: LAN connectors used, 1, 2, 3, 4, ---.

7. SAT: Satellite position of currently active satellite profile.

8. RX: RX polarisation of currently active satellite profile. H (horizontal), V (vertical),

L (left-hand) R (right-hand).

9. RF tracking frequency in GHz and LNB LO Frequency.

10.TX:XTX polarisation of currently active satellite profile. X (Cross polarisation) or Co

(Co-pol).

After 1 hour the display is dimmed to lowest intensity. Press any key to light up the
display.

5.4.2

Navigating the menus

Use the keypad to navigate the menus.

• Press

to select a menu item.

• Use the arrow keys

and

to go through the menu items or

enter a number, digit by digit.

• Use the arrow keys

and

to go through the settings and move

from one digit to the next.

• Press

to select a setting.

• Press

again to move one level up. If applicable, confirm to store the new setting by

pressing

►

▲

▼

◄

►

◄

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды