Furuno FV-110 Скачать руководство пользователя страница 212

Страница: 212 / 240

List of ACU events

G-8

G.3

List of ACU events

0A065-0

Antenna

ERROR

Deploy/Stow

Deploy/stow error. The antenna did not properly
unlock (deploy), or the stow switch never closed
(stow).

0A066-0

Antenna

ERROR

OMT error

Problem with OMT. Temperature may be too
high. OMT cable may be broken.

Error code

(ID)

Unit

Severity

Description

Explanation

Table G-1: ADU event messages (Continued)

Error

code (ID)

ACU

PCB

Severity

Description

Explanation

08060-0

ADM

WARNING

ADU modem

ACU/ADU communication error detected
(framing and parity). If the situation is persistent,
check if cable specifications comply (length and
attenuation).

08061-0

ADM

WARNING

VMU linux shell
password

The specified password (root) for the VSAT
modem is not accepted by the modem.

08062-0

ADM

WARNING

VMU debug shell
password

The specified password (user) for the VSAT
modem is not accepted by the modem.

08063-0

ADM

ERROR

ADU connection

The ACU has lost connection with the antenna.

08064-0

ADM

ERROR

ADM PLL lock

The intermediate frequency PLL is not in lock.
Check the 10 MHz reference signal.

08065-0

ADM

WARNING

GNSS data

Missing GNSS data (fix).

08066-0

ADM

WARNING

Heading data

Missing heading information. Check cable and
heading provider device.

08067-0

ADM

ERROR

PCB temperature

ADM temperature too high. Make sure there is
compliance with the environmental
specifications.

08068-0

ADM

ERROR

PSM power

The PSM fails to provide the requested supply
voltage.

08069-0

ADM

WARNING

Blocking Zone

The antenna has entered a blocking zone.

0806A-0

ADM

WARNING

VMU connection

The ACU has lost connection with the sat
modem.

Table G-2: ACU event messages

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды