Furuno FV-110 Скачать руководство пользователя страница 111

Страница: 111 / 240

Keypad and menus of the ACU

5-49

Top-level menu

Menu descriptions

Top-level

Description

MAIN

View with current status of the FV-110. Example when
logged on to the satellite:

This view is displayed after a time out of 10 minutes. Press
any key (except left arrow) to enter the menu at

MAIN

New events are shown in this display. If an event is
displayed, press

to jump directly to the menu

EVENTS

for viewing the currently active events.

ANTENNA

Shows the current ADU parameters, position, software
version and serial numbers of the ADU and ACU.

MODEM

Selected VMU type and setup, including signal level.

NETWORK

Shows the IP addresses and netmasks of the LAN
connectors of the ACU and the management mask.

SATELLITE

Current satellite information. This information is entered
using the web interface.

EVENTS

View system events. Active events are shown as: X
ACTIVE EVENTS in the

MAIN

display. Press

update the list.

Table 5-19: Top-level menus of the ACU

ANTENNA

Description

POINTING

ANTENNA STATE: Current state of the antenna, e.g.
TRACKING
ELEVATION: Current elevation angle of the antenna
AZIMUTH: Current azimuth of the antenna, with reference
to North

POLARISATION

RX POLARISATION: HORIZONTAL or VERTICAL,
read from connected VSAT modem.TX POLARIZATION:
X-POL or Co-POL, read from connected VSAT modem.

Table 5-20: ANTENNA menu of the ACU

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды