Furuno FV-110 Скачать руководство пользователя страница 84

Страница: 84 / 240

Configuration with the web interface

5-22

BUC TX information

The BUC TX information is displayed on the

DASHBOARD

in the section

TX. BUC

indicates if the FV-110 has enabled the BUC or not. It can show

Off

. This

information is also shown in the display of the ACU as TX ON or TX OFF. The FV-110
shows

BUC TX On

when the following conditions are met:

• The FV-110 must sense the 10 MHz Tx reference signal from the connected VSAT

modem.

• The VSAT modem must have Rx lock.

• The antenna must point correctly to the satellite.

• The antenna must be in tracking mode.

5.3.2

Modem profiles and satellite profiles

Modem profiles

A modem profile contains all modem settings that are necessary for a successful
connection to the satellite. The data you have to fill in are provided by your VSAT service
and modem provider. You must add at least one modem profile.

Figure 5-16: Web interface: SETTINGS, Modem profiles — list (example)

On the page

Modem profiles

you create, edit or delete Modem profiles. The supported

Modem profiles are listed in the drop-down list

Modem

DUAL ANTENNA parameter

Description

DUAL ANTENNA MASTER
or DUAL ANTENNA SLAVE

This is the Dashboard for the master or the slave
antenna. See also

Dual antenna mode (optional)

page 5-36.

Status

Shows the current status for the antenna (Master or
Slave)

Show master dashboard or
Show slave dashboard

Click here to switch to the dashboard of the other
antenna in the dual antenna system.

Table 5-13: Web interface, DASHBOARD, dual antenna (option)

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды