Furuno FV-110 Скачать руководство пользователя страница 82

Страница: 82 / 240

Configuration with the web interface

5-20

• Safe Mode

(error, followed by an error description)

• Service switch

(service switch in ADU activated)

• Ready

(waiting for data from the modem or no satellite profile selected)

• Pointing antenna

(locating the satellite)

• Acquiring signal

(acquiring the satellite signal)

• Tracking

(tracks the current satellite)

• Lineup

(line up is activated)

• Azimuth calibration

• TX cable calibration

• Test

• Not ready

(waiting for input from GNSS, e.g. GPS)

• Not ready: Initializing

• Not ready: Need pos

• Blocking zone

(antenna is pointing into a blocking zone)

• No TX zone

(antenna is pointing in a no TX zone; TX is off

Sections on the Dashboard

FV-110 parameter

Description

GNSS position

Current position of the vessel, reported by the GPS module

Vessel heading

Ship’s heading in degrees with reference to North, provided by
the ship’s gyro.

Satellite profile

Name of the currently active satellite profile.

Satellite position

Position of the satellite selected in Satellite profile.

RX polarisation

Horizontal or vertical.

TX polarisation

Co-pol or X-pol, auto-selected by VSAT modem

RX RF frequency

Ku band receiving frequency, auto-selected by VSAT modem

LNB Lo
frequency

Auto-selected by VSAT modem

TX RF frequency

Auto-selected by VSAT modem

BUC Lo frequency 12.8 GHz (system parameter)

Tracking RF
frequency

Current RF tracking frequency.

Table 5-9: Web interface, DASHBOARD, FV-110 parameters

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды