Furuno FV-110 Скачать руководство пользователя страница 87

Страница: 87 / 240

Configuration with the web interface

5-25

Figure 5-19: Web interface: SETTINGS - list of satellite profiles (example)

Each satellite profile has one assigned VSAT modem profile.

To add or edit a satellite profile, do as follows:

1. Go to

SETTINGS or Satellite profiles

and click

Edit

New entry

Figure 5-20: Web interface: SETTINGS, Satellite profiles — new entry (example)

2. Enter or edit the Satellite profile name.

3. Select a VSAT modem profile. The page automatically displays the parameters

available for the selected VSAT modem profile.
For instruction how to add a VSAT modem profile see

Modem profiles

on page 5-22.

4. Enter the data for the satellite that you want to use. For satellite data see

DVB-S

satellites

on page E-1 or

www.lyngsat.com.

5. Polarisation skew: See documents from VSAT provider.

Note

It is helpful to assign a name containing the location where the Satellite
profile is to be used (e.g.

Gulf of Mexico

North Sea

) and possibly the

provider.

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды