Furuno FV-110 Скачать руководство пользователя страница 130

Страница: 130 / 240

Removal and replacement of the ACU

7-8

7.3.2

LEDs in the ACU

The ACU has 3 LEDs: Power, Logon and Fail/Pass LED.

7.4

Removal and replacement of the ACU

There are no parts in the ACU that you can remove or replace. Contact your dealer for
further repair or replacement.

Figure 7-6: LEDs on the ACU

LED

Behaviour

Description

Power

Steady green

Power supply OK

Steady red

Power supply failure

Off

No power

Logon

Flashing green Current status is displayed:

• Searching satellite
• Identifying satellite
• Carrier lock & TX enabled from modem

Steady green

Satellite link established

Off

No satellite link acquired

Fail/Pass
LED

Steady red

A fault which prevents operation is present
in the system (ACU, ADU, MODEM).

Flashing green A Power On Self Test (POST) or Person

Activated Self Test (PAST) in progress.
The current status is displayed.

Flashing red

Active BITE failure or warning. The event
is shown in the ACU display.

Steady green

No faults.

Table 7-2: LEDs on the ACU

LEDs

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды