Furuno FV-110 Скачать руководство пользователя страница 42

Страница: 42 / 240

Installation of the ADU

2-18

2.3

Installation of the ADU

The ADU is shipped fully assembled. You have to install it on the mast and attach the
ADU cable.

Before installing the ADU read the following guidelines.

WARNING!

Use a strong webbed sling with a belt to

lift the ADU without damaging the radome. Make sure
that the sling can carry the ADU’s weight126,5 kg (FV-
110).

WARNING!

The ADU may be subject to swaying

motions in windy conditions. Always use tag lines to
stabilise the ADU during hoisting.

Figure 2-14: FV-110: Use of strong sling with a belt and tag lines for safe

hoisting

Tag lines

Webbed sling with belt

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды