Furuno FV-110 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 240

background image

STM SatLink 2900 VSAT modem

C-22

C.6

STM SatLink 2900 VSAT modem

C.6.1

Interfaces and VSAT modem configuration

The following sections describe how to connect an ACU to an STM SatLink 2900 VSAT
modem. The STM SatLink 2900 and the FV-110 are fully integrated and require almost
no user setup.

STM SatLink 2900 software version required: 14.2.0 or higher.

Connections and login

1. Connect the ACU and STM SatLink 2900 with the following cables:

• Ethernet cable for TCP/IP data communication. Connect LAN A on the VSAT modem

to LAN 1 on the ACU.

• 75 Ohm RF cables F-F connectors for RX and TX frequencies

Figure C-17: Connecting STM SatLink 2900 VSAT modem to the ACU

2. Connect a PC to the modem via serial (setting: 38400, 8, N, 1) or telnet.

3. Login to the modem with the user name and password received from the VSAT service

provider.

Example

: Login: root

             Password: *******
             SatLink 2900
             - Main board ID 120265, Revision R4.0
             - SW ID 120208, Revision 16.0.0 Build 46

4. Check that the modem has software version 14.2.0 or higher. Earlier modem software

versions are not supported.

«
...
162
163
164
165
166
...
»

Содержание FV-110

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FV-110

Бренд: Yaesu Страницы: 2

Бренд: Dish Network Страницы: 22

NextG 007GTi PRO

Бренд: Datacom Страницы: 35

Бренд: Televes Страницы: 24

Бренд: AR Страницы: 38

Бренд: AR Страницы: 26

ValuLine VHLP1 Series

Бренд: CommScope Страницы: 13

Бренд: New Eagle Страницы: 14

Бренд: Cabletech Страницы: 12

PowerBean fante

Бренд: Ubiquiti Страницы: 24

Бренд: Philex Страницы: 2

Бренд: Magnadyne Страницы: 2

Бренд: Labgear Страницы: 2

Бренд: Cessna Страницы: 2

Бренд: Syntonics Страницы: 19

Бренд: Simrad Страницы: 40

AlarmNet 7845GSM

Бренд: Honeywell Страницы: 2

Бренд: TracVision Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды