Furuno FV-110 Скачать руководство пользователя страница 112

Страница: 112 / 240

Keypad and menus of the ACU

5-50

GNSS

LATITUDE: current latitude, read from GPS module.
LONGITUDE: current longitude, read from GPS module.
FIX TYPE: 2D or 3D

HEADING

Ship’s heading in degrees with reference to North, provided
by the ship’s gyro.

VERSIONS

Current software version.

SERIAL
NUMBERS

ACU: ACU serial number;
ADU: Serial number of the antenna

MODEM menu

Description

MODEM TYPE

Connected modem type.

TX ENABLE

On or off, information delivered by the connected VSAT
modem.

RX LOCK

On or off, information delivered by the connected VSAT
modem.

SIGNAL
LEVEL

Current input signal level from VSAT modem.
iDirect openAMIP modem: (PWR) 0-500, delivered by the
connected modem. For values <250 the antenna searches after
a new signal.
Other modem: Signal level in dB.

Table 5-21: MODEM menu of the ACU

NETWORK menu

Description

HOST NAME

Current host name

PORT 1/2 IP

Current IP address for LAN 1 and LAN 2.

PORT 1/2 MASK

Current netmask for LAN 1 and LAN 2.

PORT 3 IP

(LAN 3) Current IP address of the FV-110 web interface
(default: 192.168.0.1).

PORT 3 MASK

(LAN 3) Current netmask of the FV-110 web interface
(default: 255.255.255.0).

PORT 4 IP

Current IP address for LAN 4.

PORT 4 MASK

Current netmask for LAN 4.

DEFAULT
GATEWAY

Current default gateway.

Table 5-22: NETWORK menu of the ACU

ANTENNA

Description

Table 5-20: ANTENNA menu of the ACU (Continued)

Содержание FV-110

















































































































































































































































Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды

Furuno FV-110, Руководство оператора

Результаты поиска

Содержание FV-110

Отзывы:

Похожие инструкции для FV-110

Бренды по названию

Популярные бренды