Furuno FCV-38 Скачать руководство пользователя страница 88

Страница: 88 / 152

4. ADVANCED SETTINGS

4-6

SIZE1 - SIZE3 menu

4.5

Alarm Menu

All alarms and their respective conditions can be set from the Alarm section of the [Ad-
vanced Settings] menu. For further details on setting alarms and their conditions, see
section 1.22.

4.6

External Echo Sounder Menu

The external echo sounder can be set from the [External Echo Sounder] section of the
[Advanced Settings] menu.

Note 1:

The [External Echo Sounder] menu is available only when the DFF3 is con-

nected.

Note 2:

Where [External Fish Finder Window] is set to [On] at installation, you can ac-

cess external fish finder setting from a sub monitor by right-clicking a non-interactive
section of the screen. See section 4.8.

FCV-38[ver 0252474-xx.xx]

FCV-38[ver 0252473-xx.xx]

Содержание FCV-38

























































































































































Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды

Furuno FCV-38, Руководство пользователя

Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды